51
製冰機清潔
（按
5
秒閃爍）
製冰機清潔
（按
5
秒閃爍）
HOW TO MAINTAIN THE AUTOMATIC ICE MAKER
Ice Maker
Cleaning
Ice tray
●
Maintain it once a year
Water supply container
Ice tray and water supply line can be washed.
Be sure to check the followings before starting the operation.
Go to the next step after checking them.
●
When using for the fi rst time
●
When not used for more than one week
●
Recommended maintenance intervals
●
Remove the seal from the lid and wash it with a
soft wash sponge.
●
How to open the lid
●
How to close the lid
1
1
1
Push the
製冰
button and hold it for more
than 5 seconds after closing all the doors
and turning on the display.
Release the button when
大顆
/
標準
/
停止
indicator lamps fl ash and the buzzer sounds. Ice
Maker Cleaning will start.
Push the
製冰
button to stop supplying water to the ice
tray and turn on the
停止
indicator lamp. (Stop ice making)
Empty the ice tray and wash it lightly in the stream.
Push the
製冰
button to turn on the indicator lamp.
(Automatic Ice Making
starts)
Turn the case and remove it
from the lid.
Pull the tab of the water
fi lter with fi ngers and
remove it from the case.
Wash it with a soft
wash sponge etc.
The buzzer will stop and the indicator lamp will be
turned off in about 3 minutes. After that, remove
water in the Ice case and wipe the case.
Make sure that water does not spill
out when removing the case.
Open the Ice Compartment Door.
①
Pull down the lever and
②
draw the frame.
③
Raise the cover (
▲
part) in the direction of the arrow.
④
Remove the ice tray from the frame.
・
The indicator lamp will fl ash and the buzzer will sound for about
3 minutes.
・
製冰機清潔
(Ice Maker Cleaning) can’t be interrupted.
・
Opening any door of the refrigerator during the Ice Maker
Cleaning may cause malfunction. Do not open/close any door
until Ice Maker Cleaning fi nishes.
・
Alarm will sound even after stopping the Door Alarm.
Water which doesn't contain chlorine may easily cause slime and/
or fur compared with tap water. Wash the Water Supply Container
regularly to prevent bacteria from breeding when such water is used.
There is no problem with using water remaining in the water supply
container, if any.
※
If the indicator lamp
fl ashes, perform the
following operation after
the “
停止
” lamp is
turned on in 20 seconds.
2
2
2
3
3
How To Remove Parts / How to Maintain the Automatic Ice Maker
About
5 seconds
1 beep
4 long beeps
Tap water
Mineral water, well water, water purifi ed by water
purifi er, cooled boiled water, etc. (water which doesn't
contain chlorine)
Once a week
Once three
days
Water supply
cover
Seal
(Front)
Insert the lid from its rear side and
close it in the direction of the arrow.
(Back)
Lid
Case
Water fi lter
Water supply
container
Container-full
line
Add water line
Tab
Water fi lter
(Replace it normally every 3
〜
4 years.)
Pg.57
Do not use the
detergents etc.
Do not use any cleaning
tool that can scratch it easily
such as scrubbing brush and
plate powder.
●
Wash the water supply container thoroughly and
replace it after drying it if you stop ice making and you
are not to use the Automatic ice maker for a while.
●
In particular, dry the water fi lter thoroughly.
Notice
Light ON
Cover
Press this button to turn on
the
停止
indicator lamp.
4
▲
part
Frame
Lever
Is the lever in
horizontal state?
Lever
Horizontal
Click
①
Set the ice tray and
②
close the cover.
③
Make the frame horizontal and push
it into the end, and
④
Pull up the lever.
Push this button to turn
on the indicator lamp
Light ON
●
If you cannot push the frame of the ice tray into the end, the ice tray drive motor may have operated.
Remove the ice tray once and push the frame in, and wait 1 minute after closing the Ice Compartment Door.
Preparation for the ice tray drive motor fi nishes, and you can set the ice tray.
Notice
●
Water supply container
・
Water is fi lled in it.
・
The container is set properly as
specifi ed.
●
Ice case
・
If there remains ice, remove it.
製冰機清潔
（按
5
秒閃爍）
Press this button for
more than 5 seconds
