manualshive.com logo in svg

Hitachi HTS721010G9AT00, Технические характеристики

Жесткий диск Hitachi HTS721010G9AT00 - это надежное устройство емкостью 1000 Гб с интерфейсом SATA. Здесь вы можете скачать бесплатно его техническое руководство с подробными характеристиками и инструкциями по эксплуатации на manualshive.com. Не теряйте время, скачайте свой руководство уже сегодня!

Поделиться
Скачать
background image

Travelstar 7K100 Hard Disk Drive Specification

77

11.9.4.4  User Password lost

If the User Password is forgotten and High level security is set, the system user cannot access any data. However 
the device can be unlocked using the Master Password.

If a system user forgets the User Password and Maximum security level is set, data access is impossible. However 
the device can be unlocked using the Security Erase Unit command to unlock the device and erase all user data with 
the Master Password.

Figure 4: Password lost

11.9.4.5  Attempt limit for the SECURITY UNLOCK command

The SECURITY UNLOCK command has an attempt limit, the purpose of which is to prevent someone from 
attempting to unlock the drive with various passwords numerous times.

The device counts the password mismatch. If the password does not match, the device counts it without 
distinguishing the Master password and the User password. If the count reaches 5, EXPIRE bit (bit 4) of Word 128 
in Identify Device information is set, and the SECURITY ERASE UNIT command and the SECURITY UNLOCK 
command are then aborted until there is a hard reset or a power off. The count and EXPIRE bit are cleared after a 
power on reset or a hard reset.

User Password Lost

LEVEL ?  High

Maximum

Erase Prepare Command
Erase Unit Command
  with Master Password

Normal operation but data lost

Unlock EMD with Master Password

Normal operation

Содержание HTS721010G9AT00


































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HTS721010G9AT00

IBM DS8000 - ADDITIONAL INFORMATION Manual preview
DS8000 - ADDITIONAL INFORMATION
Бренд: IBM Страницы: 5
IBM System Storage TS7600 ProtecTIER Series Software Upgrade Manual preview
System Storage TS7600 ProtecTIER Series
Бренд: IBM Страницы: 132
IBM Storwize V7000 Troubleshooting And Maintenance Manual preview
Storwize V7000
Бренд: IBM Страницы: 188
OEM Tools 24739 Operating Instructions And Parts Manual preview
24739
Бренд: OEM Tools Страницы: 4
QNAP TS-464U User Manual preview
TS-464U
Бренд: QNAP Страницы: 69
LaCie FastKey User Manual preview
FastKey
Бренд: LaCie Страницы: 54
StarTech.com RAIDBAY3 Installation Manual preview
RAIDBAY3
Бренд: StarTech.com Страницы: 7
Rocstor ROCSERVE 4RMe Installation And Configuration Manual preview
ROCSERVE 4RMe
Бренд: Rocstor Страницы: 132
Frontier WB602201 Manual preview
WB602201
Бренд: Frontier Страницы: 6
Frontier CT5401B Manual preview
CT5401B
Бренд: Frontier Страницы: 9
Netstor NA380A-G3 User Manual preview
NA380A-G3
Бренд: Netstor Страницы: 11
Seville Classics UltraHD 20206 Assembly Instructions Manual preview
UltraHD 20206
Бренд: Seville Classics Страницы: 7
Rocstor ROCPORT ID3 Quick Installation Manual preview
ROCPORT ID3
Бренд: Rocstor Страницы: 4
Asus Travelair-AC User Manual preview
Travelair-AC
Бренд: Asus Страницы: 32
Asus EHD-A1T Quick Start Manual preview
EHD-A1T
Бренд: Asus Страницы: 40
Asus WL-HDD User Manual preview
WL-HDD
Бренд: Asus Страницы: 58
Asus FrontLinker User Manual preview
FrontLinker
Бренд: Asus Страницы: 10
Asus Zendisk AS400 User Manual preview
Zendisk AS400
Бренд: Asus Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды