manualshive.com logo in svg

Hitachi HTS721010G9AT00, Технические характеристики

Поделиться
Скачать
Hitachi HTS721010G9AT00 Скачать руководство пользователя страница 166

Travelstar 7K100 Hard Disk Drive Specification

152 

13.31  Security Unlock (F2h)

Table 106: Security Unlock (F2h)

This command unlocks the password and causes the device to enter device unlock mode. If a power on reset or 
hard reset is done without executing the Security Disable Password command after this command is completed, the 
device will be in device lock mode. The password has not been changed yet.

The Security Unlock command requests to transfer a single sector of data from the host including information spec-
ified in the table below.

If the Identifier bit is set to master and the drive is in high security mode, the password supplied will be compared 
with the stored master password. If the drive is in maximum security mode, the security unlock will be rejected.

If the Identifier bit is set to user, the drive compares the supplied password with the stored user password.

If the password compare fails, the device returns an abort error to the host and decrements the unlock attempt 
counter. This counter is initially set to 5 and is decremented for each password mismatch. When this counter 
reaches zero, all password protected commands are rejected until there is a hard reset or a power off.

Identifier

 

A zero indicates that the device regards Password as the User Password. A one indicates that the 
device regards Password as the Master Password.

The user can detect if the attempt to unlock the device has failed due to a mismatched password since this is the 
only reason that an abort error will be returned by the drive AFTER the password information has been sent to the 
device. If an abort error is returned by the device BEFORE the password data has been sent to the drive, then 
another problem exists.

Command Block Output Registers

Command Block Input Registers

Register

7 6 5 4 3 2 1 0

Register

7 6 5 4 3 2 1 0

Data

- - - - - - - -

Data

- - - - - - - -

Feature

- - - - - - - -

Error

see below

Sector Count

- - - - - - - -

Sector Count

- - - - - - - -

LBA Low

- - - - - - - -

LBA Low

- - - - - - - -

LBA Mid

- - - - - - - -

LBA Mid

- - - - - - - -

LBA High

- - - - - - - -

LBA High

- - - - - - - -

Device

1 - 1 D - - - -

Device

- - - - - - - - 

Command

1 1 1 1 0 0 1 0

Status

see below

Error Register

Status Register

7

6

5

4

3

2

1

0

7

6

5

4

3

2

1

0

CRC

UNC

0

IDN

0

ABT

T0N

AMN

BSY RDY

DF

DSC

DRQ

COR IDX

ERR

0

V

0

0

0

V

0

0

0

V

0

-

-

0

-

V

Word

Description

00

Control Word   

  bit 0      : Identifier (1- Master, 0- User)   

  bit 1-15  : Reserved             

01-16

Password (32 bytes)

17-255 Reserved

Содержание HTS721010G9AT00


































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды