manualshive.com logo in svg

Hitachi HTS721010G9AT00, Технические характеристики

Поделиться
Скачать
Hitachi HTS721010G9AT00 Скачать руководство пользователя страница 161

Travelstar 7K100 Hard Disk Drive Specification

147

 

13.28  Security Erase Unit (F4h)

Table 101: Security Erase Unit (F4h)

The Security Erase Unit command initializes all user data sectors and then disables the device lock function.

Note that the Security Erase Unit command initializes from LBA 0 to Native MAX LBA. The Host MAX LBA is 
set by the Initialize Drive Parameter or the Set MAX ADDRESS command is ignored. The protected area by the 
Set MAX ADDRESS command is also initialized.

This command requests the transfer of a single sector of data from the host including information specified in the 
table below.

If the password does not match, the device rejects the command with an Aborted error.

Table 102: Erase Unit information

Identifier 

Zero indicates that the device should check the supplied password against the user password stored 
internally. One indicates that the device should check the given password against the master pass-
word stored internally.

The Security Erase Unit command erases all user data and disables the security mode feature (device lock func-
tion). After completing of this command, all the user data will be initialized to zero with a write operation. At this 
time, the data write is not verified with a read operation to determine if the data sector is initialized correctly. At 
this time the defective sector information and the reassigned sector information for the device are not updated. The 
security erase prepare command should be completed immediately prior to the Security Erase Unit command. If 
the device receives a Security Erase Unit command without a prior Security Erase Prepare command, the device 
aborts the security erase unit command.

Command Block Output Registers

Command Block Input Registers

Register

7 6 5 4 3 2 1 0

Register

7 6 5 4 3 2 1 0

Data

- - - - - - - -

Data

- - - - - - - -

Feature

- - - - - - - -

Error

see below

Sector Count

- - - - - - - -

Sector Count

- - - - - - - -

LBA Low

- - - - - - - -

LBA Low

- - - - - - - -

LBA Mid

- - - - - - - -

LBA Mid

- - - - - - - -

LBA High

- - - - - - - -

LBA High

- - - - - - - -

Device

1 - 1 D - - - -

Device

- - - - - - - - 

Command

1 1 1 1 0 1 0 0

Status

see below

Error Register

Status Register

7

6

5

4

3

2

1

0

7

6

5

4

3

2

1

0

CRC

UNC

0

IDN

0

ABT

T0N

AMN

BSY RDY

DF

DSC

DRQ

COR IDX

ERR

0

0

0

V

0

V

0

0

0

V

0

V

-

0

-

V

Word

Description

00

Control Word   

  bit 0      : Identifier (1- Master, 0- User)   

  bit 1-15  : Reserved             

01-16

Password (32 bytes)

17-255

Reserved

Содержание HTS721010G9AT00


































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды