manualshive.com logo in svg

Hitachi HTS721010G9AT00, Технические характеристики

Жесткий диск Hitachi HTS721010G9AT00 - это надежное устройство емкостью 1000 Гб с интерфейсом SATA. Здесь вы можете скачать бесплатно его техническое руководство с подробными характеристиками и инструкциями по эксплуатации на manualshive.com. Не теряйте время, скачайте свой руководство уже сегодня!

Поделиться
Скачать
background image

Travelstar 7K100 Hard Disk Drive Specification

72

increase with increasing advanced power management levels. The advanced power management levels contain 
discrete bands, described in the section of Set Feature command in detail.

This feature set uses the following functions:

• A SET FEATURES subcommand to enable Advanced Power Management
• A SET FEATURES subcommand to disable Advanced Power Management

The Advanced Power Management feature is independent of the Standby timer setting. If both Advanced Power 
Management level and the Standby timer are set, the device will go to Standby state when the timer times out or the 
device's Advanced Power Management algorithm indicates that it is time to enter the Standby state.

The IDENTIFY DEVICE response word 83, bit 3 indicates that Advanced Power Management feature is supported 
if set. Word 86, bit 3 indicates that Advanced Power Management is enabled if set. Word 91, bits 7-0 contains the 
current Advanced Power Management level if Advanced Power Management is enabled.

11.7.1  Performance Idle Mode

This mode is usually entered immediately after Active mode command processing is complete, instead of 
conventional idle mode. In Performance Idle mode, all electronic components remain powered and full frequency 
servo remains operational. This provides instantaneous response to the next command. The duration of this mode is 
intelligently managed as described below.

11.7.2  Active Idle Mode

In this mode, power consumption is 45–55% less than that of Performance Idle mode. Additional electronics are 
powered off and the head is parked near the mid-diameter of the disk without servoing. Recovery time to Active 
mode is about 20 ms.

11.7.3  Low Power Idle Mode

Power consumption is 60–65% less than that of Performance Idle mode. The heads are unloaded on the ramp but 
the spindle is still rotated at the full speed. Recovery time to Active mode is about 300 ms.

11.7.4  Transition time

The transition time is dynamically managed by the user's recent access pattern, instead of fixed times. The ABLE-3 
algorithm monitors the interval between commands instead of the command frequency of ABLE-2. The algorithm 
supposes that the next command will come with the same command interval distribution as the previous access 
pattern. The algorithm calculates the expected average saving energy and response delay for next command in 
several transition time case based on this assumption. And it selects the most effective transition time with the 
condition that the calculated response delay is shorter than the value calculated from the specified level by Set 
Feature Enable Advanced Power Management command.

The optimal time to enter Active Idle mode is variable depending on the recent behavior of the user. It is not possible 
to achieve the same level of Power savings with a fixed entry time into Active Idle because every user's data and 
access pattern is different. The optimum entry time changes over time.

The same algorithm works for entering into Low Power Idle mode and Standby mode, which consumes less power 
but needs more recovery time switching from this mode to Active mode.

Содержание HTS721010G9AT00


































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HTS721010G9AT00

Falcon 165 Instructions For Assembly preview
165
Бренд: Falcon Страницы: 19
G-Technology G-RAID Studio Instructions Manual preview
G-RAID Studio
Бренд: G-Technology Страницы: 32
G-Technology G-DRIVE ev ATC Product Manual preview
G-DRIVE ev ATC
Бренд: G-Technology Страницы: 35
Western Digital My Passport for Mac Quick Start preview
My Passport for Mac
Бренд: Western Digital Страницы: 2
Qualstar RLS-4470 Technical & Service Manual preview
RLS-4470
Бренд: Qualstar Страницы: 205
OCZ VERTEX 2 SATA II 3.5 Datasheet preview
VERTEX 2 SATA II 3.5
Бренд: OCZ Страницы: 3
Schaffner HOLZLAGER 7021 Assembly Instructions preview
HOLZLAGER 7021
Бренд: Schaffner Страницы: 4
WiebeTech Forensic ComboDock FCDv6 Manual preview
Forensic ComboDock FCDv6
Бренд: WiebeTech Страницы: 20
garofalo BAULE EVO 80 BAULE EVO 120 User Manual preview
BAULE EVO 80 BAULE EVO 120
Бренд: garofalo Страницы: 16
Synology DiskStation Series Upgrade Installation Instructions preview
DiskStation Series
Бренд: Synology Страницы: 6
OWC MERCURY ELITE PRO MINI Manual preview
MERCURY ELITE PRO MINI
Бренд: OWC Страницы: 8
IBM 10/20 GB TR-5 User Manual preview
10/20 GB TR-5
Бренд: IBM Страницы: 36
Kreg Universal Bench Assembly Instructions Manual preview
Universal Bench
Бренд: Kreg Страницы: 12
RaxGo RGFSKR User Manual preview
RGFSKR
Бренд: RaxGo Страницы: 8
Toshiba MK3252GSX Features And Specifications preview
MK3252GSX
Бренд: Toshiba Страницы: 1
Toshiba MK2552GSX Features And Specifications preview
MK2552GSX
Бренд: Toshiba Страницы: 1
Toshiba MK4007GAL Installation Notes preview
MK4007GAL
Бренд: Toshiba Страницы: 4
Toshiba MK2529GSG Specifications preview
MK2529GSG
Бренд: Toshiba Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды