manualshive.com logo in svg

Hitachi HTS721010G9AT00, Технические характеристики

Поделиться
Скачать
Hitachi HTS721010G9AT00 Скачать руководство пользователя страница 181

Travelstar 7K100 Hard Disk Drive Specification

167

 

13.39.1.7  S.M.A.R.T. Read Log Sector (subcommand D5h)

This command returns the specified log sector contents to the host.

The 512 bytes of data are returned at a command and the Sector Count value shall be set to one. The LBA Low 
shall be set to specify the log sector address.

13.39.1.8  S.M.A.R.T. Write Log Sector (subcommand D6h)

This command writes 512 bytes of data to the specified log sector. The 512 bytes of data are transferred at a com-
mand and the LBA Low value shall be set to one. The LBA Low shall be set to specify the log sector address (See 
Table 114:  “S.M.A.R.T. Function Set (B0h)” on page 163). If a Read Only log sector is specified, the device 
returns ABRT error.

13.39.1.9  S.M.A.R.T. Enable Operations (subcommand D8h)

This subcommand enables access to all S.M.A.R.T. capabilities within the device. Prior to receipt of a S.M.A.R.T. 
Enable Operations subcommand, Attribute Values are neither monitored nor saved by the device. The state of 
S.M.A.R.T.—either enabled or disabled—will be preserved by the device across power cycles. Once enabled, the 
receipt of subsequent S.M.A.R.T. Enable Operations subcommands will not affect any of the Attribute Values. 

Upon receipt of the S.M.A.R.T. Enable Operations subcommand from the host, the device asserts BSY, enables 
S.M.A.R.T. capabilities and functions, clears BSY, and asserts INTRQ.

13.39.1.10  S.M.A.R.T. Disable Operations (subcommand D9h)

This subcommand disables all S.M.A.R.T. capabilities within the device including the device's attribute auto save 
feature. After receipt of this subcommand the device disables all S.M.A.R.T. operations. Non self-preserved 
Attribute Values will no longer be monitored. The state of S.M.A.R.T.—either enabled or disabled—is preserved 
by the device across power cycles. Note that this subcommand does not preclude the device's power mode attribute 
auto saving.

Upon receipt of the S.M.A.R.T. Disable Operations subcommand from the host, the device asserts BSY, disables 
S.M.A.R.T. capabilities and functions, clears BSY, and asserts INTRQ.

After receipt of the device of the S.M.A.R.T. Disable Operations subcommand from the host, all other S.M.A.R.T. 
subcommands—with the exception of S.M.A.R.T. Enable Operations—are disabled, and invalid and will be 
aborted by the device—including the S.M.A.R.T. Disable Operations subcommand— returning the error code as 
specified in Table 125:  “S.M.A.R.T. Error Codes” on page 180.

Any Attribute Values accumulated and saved to volatile memory prior to receipt of the S.M.A.R.T. Disable Opera-
tions command will be preserved in the device's Attribute Data Sectors. If the device is re-enabled, these Attribute 
Values will be updated, as needed, upon receipt of a S.M.A.R.T. Read Attribute Values or a S.M.A.R.T. Save 
Attribute Values command.

Log sector address

Content

Type

01h

S.M.A.R.T. Error Log

Read Only

03h

Extended Comprehensive 
S.M.A.R.T. error log

Read Only

06h

S.M.A.R.T. Self-test Log

Read Only

07h

Extended self-test Log

Read Only

09h

Selective self-test log

Read/Write

09h

Selective self-test log

Read/Write

80h-9Fh

Host vendor specific

Read/Write

Содержание HTS721010G9AT00


































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды