When the hardware installation is complete, you must configure the system to st
operation. The steps are as follows:
1. Login at first time. Log in to this device from the setup console. At the initial lo
attempt, the following appears as the default login account:
Login name:
operator
Password: (none)
To prevent security breaches, it is recommended that you login as the router
administrator (
admin
), create a new account using
adduser
command, and the
delete the default account using
rmuser
command. See
GR2000 Operations Gu
for more information.
2. Set up the configuration information. The configuration information defines t
operating environment, such as the IP addressing, type of network media,
routing protocol, and so on. The configuration information can be defined usi
commands and the GUI. Be sure to save the configuration information to a fi
At startup, the system uses the last-used configuration information file. For
individual commands and parameters, see
GR2000 Configuration Guide.
3. Set up the date and time. The date and time information is used as timestam
for events in the log information and creation of files. Before you start product
use of the router, set the date and time to correct values using
date
command
(see
GR2000 Operations Guide
).
Содержание GR2000 Series
