Hitachi CP-X265 Скачать руководство пользователя

Страница: 60 / 66

Troubleshooting

Regarding the indicator lamps

Lighting and flashing of the POWER indicator, the LAMP indicator, and the TEMP

indicator have the meanings as described in the table below. Please follow the

instructions within the table. If the same indication is displayed after the remedy,

or if an indication other than the following is displayed, please contact your dealer

or service company.

POWER

indicator

LAMP

indicator

TEMP

indicator

Description

Lighting

Orange

Turned

off

Turned

off

The projector is in a standby state.

Please refer to the section “Power On/Off”.

Blinking

Green

Turned

off

Turned

off

The projector is warming up.

Please wait.

Lighting

Green

Turned

off

Turned

off

The projector is in an on state.

Ordinary operations may be performed.

Blinking

Orange

Turned

off

Turned

off

The projector is cooling down.

Please wait.

Blinking

Red

(discre-

tionary)

(discre-

tionary)

The projector is cooling down. A certain error

has been detected.

Please wait until the POWER indicator finishes

blinking, and then perform the proper measure using

the item descriptions below.

Blinking

Red

Lighting

Red

Lighting

Red

Turned

off

The lamp does not light, and there is a

possibility that interior portion has become

heated.

Please turn the power off, and allow the projector to

cool down at least 0 minutes. After the projector has

sufficiently cooled down, please make confirmation of

the following items, and then turn the power on again.

• Is there blockage of the air passage aperture?

• Is the air filter dirty?

• Does the peripheral temperature exceed 35°C?

If the same indication is displayed after the remedy,

please change the lamp referring to the section “Lamp”.

Blinking

Red

Lighting

Red

Blinking

Red

Turned

off

The lamp cover has not been properly fixed.

Please turn the power off, and allow the projector to

cool down at least 45 minutes. After the projector has

sufficiently cooled down, please make confirmation

of the attachment state of the lamp cover. After

performing any needed maintenance, turn the power

on again. If the same indication is displayed after

the remedy, please contact your dealer or service

company.

Содержание CP-X265



































































Результаты поиска

Содержание CP-X265

Отзывы:

Похожие инструкции для CP-X265

Бренды по названию

Популярные бренды

Hitachi CP-X265, Руководство пользователя – Инструкция по эксплуатации

Результаты поиска

Содержание CP-X265

Отзывы:

Похожие инструкции для CP-X265

Бренды по названию

Популярные бренды