background image

 

FOR THE CUSTOMERS IN U.K.

THIS PRODUCT IS SUPPLIED WITH A TWO PIN MAINS PLUG FOR USE IN MAINLAND EUROPE.

FOR THE U.K. PLEASE REFER TO THE NOTES ON THIS PAGE.

IMPORTANT FOR UNITED KINGDOM

WORDING FOR CLASS I EQUIPMENT INSTRUCTION BOOKS AND 

The mains lead on this equipment is supplied with a 

 plug incorporating a fuse, the

value of which is indicated on the pin face of the plug. Should the fuse need to be replaced, an

ASTA or 

 approved BS 1362 fuse must be used of the same rating. If the fuse cover is

detachable never use the plug with the cover omitted. If a replacement fuse cover is required,
ensure it is of the same 

 as that visible on the pin face of the plug. Fuse covers are

available from your dealer.

DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the

power points in your home or the cable is too short to reach a power point, then obtain an

appropriate safety approved extension lead or consult your dealer.

Should it be necessary to change the mains plugs, this must be carried out by a competent

person, preferably a qualified electrician.

If there is no alternative to cutting off the mains plug, ensure that you dispose of it

immediately, having first removed the fuse, to avoid a possible shock hazard by inadvertent
connection to the mains supply.

WARNING: THIS EQUIPMENT MUST BE EARTHED

IMPORTANT

The wires in the mains lead are coloured in accordance with the following code:

Green and Yellow   Earth, Blue = Neutral, Brown = Live.

Green &Yellow

to Earth

Brown to Live

Fuse

Blue to Neutral

Cord Clamp

As these 

 may not correspond with the coloured markings identifying the terminals in

your plug, proceed as follows:

The wire which is coloured GREEN and YELLOW must be connected to the terminal in the plug
which is marked with the letter E or by the earth symbol 

 or coloured GREEN or GREEN and

YELLOW.

The wire coloured BLUE must be connected to the terminal marked with the letter N or

coloured BLUE or BLACK. The wire coloured BROWN must be connected to the terminal marked
with the letter L or coloured BROWN or RED.

Содержание CM1711ME





















Отзывы: