Hitachi C 8FS, Инструкция по эксплуатации

Страница: 7 / 35

6
English
10. Replace table insert when worn.
11. Do not use the saw to cut other than aluminium,
wood or similar materials.
12. Connect slide compound saw to a dust collecting
device when sawing.
13. Take care when slotting.
14. When transporting or carrying the tool, do not
grasp the holder. Grasp the handle instead of the
holder.
15. Start cutting only after motor revolution reaches
maximum speed.
16. Promptly cut OFF the switch when abnormality
observed.
17. Shut off power and wait for saw balde to stop
before servicing or adjusting tool.
18. During slide cutting operation, the saw must be
pushed and slided away from the operater.
19. During a miter or bevel cut the blade should not
be lifted until it has stopped rotation completely.
SPECIFICATIONS
0° 65mm
×
305mm
Miter 45° 65mm
×
220mm
Bevel 45° 45mm
×
305mm
Miter + Bevel 45° 45mm
×
220mm
Saw Blade Diameter 216mm
Miter Cutting Angle Right and left 0° – 57°
Bevel Cutting Angle Left 0° – 47°
Input 920W*
No-Load Speed 5000/min
Machine Dimensions (Width
×
Depth
×
Height) 660mm
×
1150mm
×
465mm
Weight (Net) 25 kg
* Be sure to check the nameplate on product as it is subject to change by areas.
Max. Cutting
Capacity
Height x Width
STANDARD ACCESSORIES
(1) 216 mm TCT Saw blade (mounted on tool) ..... 1
(2) Dust bag .................................................................... 1
(3) 10 mm Box wrench ................................................ 1
(4) Vise Assembly .......................................................... 1
(For England, France, Italy, Singapore)
(5) Sub Table (with four M8 flat screws) ................. 1
(For England, France)
Standard accessories are subject to change without
notice.
Standard accessories are subject to change by areas.
OPTIONAL ACCESSORIES (SOLD SEPARATELY)
(1) Guide Assembly
Optional accessories are subject to change without
notice.
APPLICATION
䡬
Cutting various types of wood.
UNPACKING
䡬
Carefully unpack the power tool and all related items
(standard accessories).
䡬
Check carefully to make certain all related items
(standard accessories) are present.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position. If
the plug is conencted to a receptacle while the trigger
switch is in the ON position, the power tool will start
operating immediately, inviting serious accident.
3. Extention cord
When the work area is removed from the power
source, use an extension cord of sufficient thickness
and rated capacity. The extension cord should be kept
as short as practicable.
4. When the tool is shipped, its movable parts are locked
by the locking pin. Move the handle a little and remove
the locking pin by pulling it as illustrated in
Fig. 2 .
5. Attach the dust bag to the main unit (Fig. 1).
6. Assembly of sub table.
Assembling the sub table using the four 8 mm flat
screws (
Fig. 4 ).
ADJUSTING THE POWER TOOL PRIOR TO USE
CAUTION
Make all necessary adjustments before inserting the plug
in the power source.
1. Check to see that the safety cover operates smoothly.
(1) When push down the handle while holding down the
lever, check that the safety cover revolves smoothly
(Fig. 3) .
(2) Next, check that the safety cover returns to the original
position when the handle is raised.
2. Saw blade height adjustment (Fig. 2).
The main unit has as standard equipment a saw blade
with an outer diameter of 216 mm and adjustable
cutting depth. Follow the steps outlined below of
adjustment when using a saw-blade with an outer
diameter which is greater than 216 mm.