manualshive.com logo in svg

Hitachi 5000 Series, Руководство по оборудованию

Поделиться
Скачать
Hitachi 5000 Series Скачать руководство пользователя страница 70

Power off procedures

Follow this procedure exactly when powering off the storage system.

Caution: Except in an emergency, do not turn off the PDU breakers before

turning off the power to the system. The system reacts as a power failure

occurred and uses the cache backup batteries to keep the cache active until

the data in the cache is transferred to the cache backup flash memory. When

the cache backup batteries discharge power, the power-on time can be

prolonged by the amount of charge remaining in the batteries. Fully

discharged batteries take 90 minutes to charge.

Note: The control panel includes a safety feature to prevent the storage

system power from being turned on or off accidentally. The PS power ON/OFF

switch does not work unless the ENABLE switch is moved to and held in

ENABLE while the power switch is moved to ON or OFF.

Before you begin

■

Confirm all maintenance and software-specific shutdown procedures have been

completed.

■

Verify all I/O activity to the storage system has stopped. You can vary paths offline

and shut down the attached hosts.

Procedure

1. In the PS area on the control panel, move the ENABLE switch to the ENABLED and

hold it there. While holding the switch in ENABLED, move the PS ON/OFF switch to

OFF. Then release both switches.

2. Wait for the storage system to complete its shutdown routines. Depending on the

storage system configuration and certain MODE settings, you can wait 20 minutes

for the storage system to copy data from the cache to the cache flash drives and for

the disk drives to spin down.
If the READY and PS LEDs do not turn OFF after 20 minutes, contact customer

support for assistance.

Emergency power off/on procedures

The following describes how to shut off the system during an emergency situation and

turning on power to the storage system after an emergency shutdown.

Turning off power to the storage system during an emergency

The storage system does not have an emergency power off switch. Use the following

procedure to turn off the system during an emergency.

Note: When turning off the storage system, first turn off the PDUs connecting

to the controllers and then turn off the PDUs connecting to the drive trays.

Power off procedures

Chapter 4: Turning storage system power on and off

Hitachi Virtual Storage Platform 5000 Series Hardware Guide

70

Содержание 5000 Series



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды