Hitachi 42PMA225EZ, Руководство по обслуживанию

Страница: 27 / 60

24
Plasma TV Service Manual 11/01/2005
IGP0 L14 O general purpose output signal 0; image port (controlled by
subaddresses 84H and 85H)
AOUT M1 O analog test output (do not connect)
V
SSA0
M2 P ground for internal Clock Generation Circuit (CGC)
V
DDA0
M3 P analog supply voltage (3.3 V) for internal clock generation
circuit
V
DDD9
M4 P Digital supply voltage 9 (peripheral cells)
V
DDD10
M5 P Digital supply voltage 10 (core)
ADP7 M6 O
MSB
−
1 of direct analog-to-digital converted output data
(VSB)
ADP2 M7 O
MSB
−
6 of direct analog-to-digital converted output data
(VSB)
V
DDD11
M8 P Digital supply voltage 11 (peripheral cells)
V
DDD12
M9 P
Digital supply voltage 12 (core)
RTS0 M10 O real-time status or sync information, controlled by
subaddresses 11H and 12H
V
DDD13
M11 P Digital supply voltage 13 (peripheral cells)
AMXCLK M12 I audio master external clock input
FSW M13 I/pd fast switch (blanking) with internal pull-down inserts
component inputs into CVBS signal
ICLK M14 I/O clock output signal for image port, or optional
asynchronous back-end clock input
TEST13 N1 NC do not connect, reserved for future extensions and for testing
TEST14 N2 I/pu do not connect, reserved for future extensions and for testing
TEST15 N3 I/pd do not connect, reserved for future extensions and for testing
CE N4 I/pu chip enable or reset input (with internal pull-up)
LLC2 N5 O line-locked 1 ¤2 clock output (13.5 MHz nominal)
CLKEXT N6 I external clock input intended for analog-to-digital conversion
of VSB signals (36 MHz)
ADP5 N7 O MSB - 3 of direct analog-to-digital converted output data
(VSB)
ADP0 N8 O LSB of direct analog-to-digital converted output data (VSB)
SCL N9 I serial clock input (I 2 C-bus)
RTS1 N10 O real-time status or sync information, controlled by
subaddresses 11H and 12H
ASCLK N11 O audio serial clock output
ITRDY N12 I target ready input for image port data
TEST16 N13 NC do not connect, reserved for future extensions and for testing
TEST17 N14 NC do not connect, reserved for future extensions and for testing
TEST18 P2 I/O do not connect, reserved for future extensions and for testing
EXMCLR P3 I/pd external mode clear (with internal pull-down)
LLC P4 O line-locked system clock output (27 MHz nominal)
RES P5 O reset output (active LOW)
ADP8 P6 O MSB of direct analog-to-digital converted output data (VSB)
ADP4 P7 O MSB - 4 of direct analog-to-digital converted output data
(VSB)
ADP1 P8 O MSB - 7 of direct analog-to-digital converted output data
(VSB)
INT_A P9 O/od I
2
C-bus interrupt flag (LOW if any enabled status bit has
changed)
SDA P10 I/O/od serial data input/output (I 2 C-bus)
AMCLK P11 O audio master clock output, up to 50% of crystal clock
ALRCLK P12 O/st/pd audio left/right clock output; can be strapped to supply via a
3.3 kW resistor to indicate
that the default 24.576 MHz crystal (ALRCLK = 0; internal
pull-down) has been replaced
by a 32.110 MHz crystal (ALRCLK = 1); see notes 5 and 7
TEST19 P13 I/pu do not connect, reserved for future extensions and for testing:
scan input
Notes
1. I = input, O = output, P = power, NC = not connected, st = strapping, pu = pull-up, pd = pull-down, od
= open-drain.