Hitachi 42PMA225EZ Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 60

background image

21

Plasma TV Service Manual

11/01/2005

• Two independent programming sets for scalar part, to define two ‘ranges’ per field or sequences over
frames
• Field wise switching between decoder part and expansion port (X-port) input
• Brightness, contrast and saturation controls for scaled outputs.

Vertical Blanking Interval (VBI) data decoder and slicer

• Versatile VBI-data decoder, slicer, clock regeneration and byte synchronization e.g. for World
Standard Teletext (WST), North-American Broadcast Text System (NABTS), close caption, Wide
Screen Signalling (WSS) etc.

Audio clock generation

• Generation of a field-locked audio master clock to support a constant number of audio clocks per
video field
• Generation of an audio serial and left/right (channel)

Digital I/O interfaces

• Real-time signal port (R port), inclusive continuous line-locked reference clock and real-time status
information supporting RTC level 3.1 (refer to document “RTC Functional Specification” for details)
• Bidirectional expansion port (X-port) with half duplex functionality (D1), 8-bit Y-C

B

-C

R

– Output from decoder part, real-time and unscaled
– Input to scalar part, e.g. video from MPEG decoder (extension to 16-bit possible)
• Video image port (I-port) configurable for 8-bit data (extension to 16-bit possible) in master mode (own
clock), or slave mode (external clock), with auxiliary timing and handshake signals
• Discontinuous data streams supported
• 32-word ´ 4-byte FIFO register for video output data
• 28-word ´ 4-byte FIFO register for decoded VBI-data output
• Scaled 4 :2 :2, 4 :1 :1, 4 :2 :0, 4 :1 :0 Y-C

B

-C

R

output

• Scaled 8-bit luminance only and raw CVBS data output
• Sliced, decoded VBI-data output.

Miscellaneous

• Power-on control
• 5 V tolerant digital inputs and I/O ports
• Software controlled power saving standby modes supported
• Programming via serial I 2 C-bus, full read back ability by an external controller, bit rate up to 400
kbits/s
• Boundary scan test circuit complies with the “IEEE Std. 1149.b1 - 1994”
• BGA156 package.

9.16.3. Pinning

SYMBOL PIN

TYPE

DESCRIPTION

XTOUT

A2

O

crystal oscillator output signal; auxiliary signal

XTALO

A3

O

24.576 MHz (32.11 MHz) crystal oscillator output; not
connected if TTL clock input of XTALI is used

V

SS(xtal)

A4

P

ground for crystal oscillator

TDO

A5

O

test data output for boundary scan test; note 2

XRDY

A6

O

task flag or ready signal from scaler, controlled by XRQT

XCLK

A7

I/O

clock I/O expansion port

XPD0

A8

I/O

LSB of expansion port data

XPD2

A9

I/O

MSB - 5 of expansion port data

XPD4

A10

I/O

MSB - 3 of expansion port data

XPD6

A11

I/O

MSB - 1 of expansion port data

TEST1

A12

I/pu

do not connect, reserved for future extensions and for testing:
scan input

TEST2

A13

I/pu

do not connect, reserved for future extensions and for testing:
scan input

AI41

B1

I

analog input 41

TEST3

B2

O

do not connect, reserved for future extensions and for testing

V

DD(xtal)

B3

P

Supply voltage for crystal oscillator

XTALI

B4

I

input terminal for 24.576 MHz (32.11 MHz) crystal oscillator
or connection of external oscillator with TTL compatible

«
...
22
23
24
25
26
...
»

Содержание 42PMA225EZ





























































Отзывы:

Нет отзывов

Похожие инструкции для 42PMA225EZ

Бренд: Dante Страницы: 12

Бренд: Digimate Страницы: 93

Бренд: iHealth Страницы: 16

Бренд: NEC Страницы: 20

Бренд: protech Страницы: 46

EEM MOT 01 FL02.01

Бренд: A&A Tech Страницы: 16

Бренд: WINGTOP Страницы: 33

Бренд: Ametek Страницы: 46

Бренд: Tommee Tippee Страницы: 10

Бренд: Pyle view Страницы: 2

Бренд: Tyco Electronics Страницы: 33

Бренд: ViewSonic Страницы: 18

Бренд: Hanns.G Страницы: 28

Бренд: VESTEL Страницы: 128

Бренд: Planar Страницы: 22

Бренд: Hyundai Страницы: 2

Бренд: ipf electronic Страницы: 25

Бренд: Elo TouchSystems Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды