Hitachi 2000 Скачать руководство пользователя страница 48

Страница: 48 / 58

Hitachi High-performance NAS Platform

8. Insert the power cord.
9. Switch the power to the ON position on the replacement PSU.

Caution:

PSU models 600 and 610 are physically interchangeable, but may not be

mixed during normal operation of a High-performance NAS Platform. If necessary,

PSU models 600 and 610 may be mixed in a High-performance NAS Platform only for

the minimum amount of time necessary to perform a hot-swap of a failed PSU (up to

72 hours). If one PSU in a High-performance NAS Platform must be replaced, and you

are replacing it with a different PSU model, replace both PSUs instead of operating

with different models of PSUs in the same High-performance NAS Platform.

Replacing a Fan Assembly

Fans provide for front-to-back airflow to be consistent with the storage system

components. The High-performance NAS Platform continues to operate following the

failure of a single fan and during the temporary removal of a fan assembly for

replacement. A failed fan must be replaced as soon as possible.
The High-performance NAS Platform fans are contained within three assemblies, which

are located behind the front fascia and are removable from the front of the High-

performance NAS Platform. All High-performance NAS Platforms have three fan

assemblies, but some models contain three fans (one fan per assembly), while other

models contain six fans (two fans per assembly).
The High-performance NAS Platform’s cooling airflow enables the system to operate in an

ambient temperature range of 10°C to 40°C when mounted in a storage cabinet with

associated components required to configure a high-performance storage system. The

storage system administrator is responsible for ensuring that the ambient temperature

within the rack does not exceed the 40°C operating limit for the High-performance NAS

Platform.

Caution:

If a fan has failed, replace the fan assembly as soon as possible to avoid

damaging the High-performance NAS Platform.

Replacing a Fan Assembly

1. Remove the High-performance NAS Platform front panel by releasing the two

latches (one each side).

Содержание 2000



























































Результаты поиска

Содержание 2000

Отзывы:

Похожие инструкции для 2000

Бренды по названию

Популярные бренды

Hitachi 2000, Справочник по аппаратуре

Результаты поиска

Содержание 2000

Отзывы:

Похожие инструкции для 2000

Бренды по названию

Популярные бренды