manualshive.com logo in svg

HIOS HSF-10, Инструкция по эксплуатации

Поделиться
Скачать
HIOS HSF-10 Скачать руководство пользователя страница 19

6-1 Replacement and adjustment of brushes

If misaligned screws are no longer swept up by the tips of the brushes, the brushes should be replaced with new items. Brushes 

with harder tips than the standard items are also available as an optional extra.

These brushes can be used to suit your requirements.

•  Turn the power switch ON/OFF and position the brush as shown on the right 

to remove the brush tips (Image 21).

  (This positions the brush mounting screws in an easy to reach location)

•  The brush tip mountings are as shown on the right.
•  Assemble the brushes in the reverse order of disassembly.
•  For adjustments, refer to “Making checks and adjustments before use”.

Brush part numbers

HSF-02107: HSF-10, HSF-12, HSF-14, HSF-17, HSF-20

HSF-22001-23: HSF-26, HSF-30 

Image 21

Mounting screws

Hexagonal socket screw 

M2.6 x 10

Spring washer M2.6

Plain washer M2.6

Brush bracket B

Brush

Brush bracket A

- 18 -

Содержание HSF-10





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды