HIOS HSF-10 Скачать руководство пользователя страница 18

Страница: 18 / 28

5. Maintenance

The transport speed of screws to be used may become slower if the rail groove becomes dirty.

If the rail is extremely dirty, use a thin cloth soaked in alcohol to clean the rail groove. The rail can be removed from the device

if you find it difficult to clean the rail. If removing the rail, ensure that the power is turned off and screws inside the panning area

removed. (Refer to “Making checks and adjustments before use” for information on how to remove the rail).

Replacement of the rail is recommended if the rail groove is so dirty or damaged that it affects operation of the device.

6. Replacement and adjustment of parts

The brushes, drive belt, and drive motor are expendable items.

Replacement rails for different sized screw threads are to be ordered separately.

The replacement and adjustment method is outlined separately.

Please read the instructions carefully before making adjustments. Remove all screws within the device before replacing parts.

Caution Replacement and adjustment should only be performed with the power switch in the OFF position.

- 17 -

Содержание HSF-10





























Результаты поиска

Содержание HSF-10

Отзывы:

Бренды по названию

Популярные бренды

HIOS HSF-10, Инструкция по эксплуатации

Результаты поиска

Содержание HSF-10

Отзывы:

Бренды по названию

Популярные бренды