Hioki MR8904 Скачать руководство пользователя страница 43

Страница: 43 / 72

5.4 Creating Condition Settings Files

Click the

[Unit1]

[Unit4]

tabs above

the

[MR8904 Analog Assign List]

and

select the position of the unit for which

the condition settings file is being cre-

ated.

(An asterisk after the unit number indicates a posi-
tion at which no unit is installed.)

Set the CAN communications condi-

tions for each port.

(Selecting the checkbox for a setting turns it on or
enables it.)

Example screen

Device



insertion position

Unit 1

CAN port 1

• High speed

• Terminator on

• ACK response enabled

• Baud rate: 500 kbps

CAN port 2

• Low speed

• Terminator off

• ACK response disabled

• Baud rate automatic detection

Setting Contents (



Default setting)

Interface

Selects the type of the CAN bus to which the unit will be connected. The following CAN

bus standards are supported:

High Speed* : ISO 11898-2

Low Speed

: ISO 11898-3

Single-wire

: SAE J2411

Terminator

When using the high-speed interface, the unit’s internal 120



termination resistor can be

connected to the bus as necessary.

On : Connects the 120



resistor between CAN-H and CAN-L.

OFF*: Does not connect the termination resistor.

ACK

Sets whether to enable sending ACK bits, error frames, and messages from the unit.

Enable : Enables sending of ACK bits, error frames, and messages.

Disable*: Disables sending of ACK bits, error frames, and messages.

Baud

Sets the CAN communications baud rate.

AUTO (automatic detection)*: Detects the baud rate automatically based on messages

being sent on the CAN bus. This setting can be used only

when ACK is disabled.

Manual setting

: Select a baud rate from 10k, 20k, 33.3k, 50k, 62.5k, 83.3k, 100k, 125k,

250k, 500k, 800k, and 1 Mbps.

Содержание MR8904









































































Результаты поиска

Содержание MR8904

Отзывы:

Бренды по названию

Популярные бренды

Hioki MR8904, Инструкция по эксплуатации

Результаты поиска

Содержание MR8904

Отзывы:

Бренды по названию

Популярные бренды