background image

Do not attempt to use this equipment unless you are trained in its proper use or are under competent 
supervision. For your safety follow the operating procedures described below every time you use the 
equipment. Deviating from these procedures may result in fire, explosion, property damage and 
operator injury. If at any time the equipment you are using does not perform in its usual manner or if 
you have any difficulty in the use of the equipment STOP using it immediately. DO NOT use the 
equipment until the problem has been corrected 
Always use torch in well ventilated area to avoid possible health hazards from fumes and smoke. 
Torches consume oxygen while in use and therefore if working in a confined space oxygen may be 
depleted.

Brazing may produce fumes and gases which may be hazardous to your health. Avoid breathing these 
fumes and gases. Read and follow the safeguards of the Material Safety Data Sheets (MSDS) for all 
brazing materials. Keep combustible material away the heat source. Keep a suitable fire extinguisher 
of the proper size in the work area. Eye protection should always be worn when brazing or soldering. 
DO NOT store the cylinders in a room used for habitation, in a closed or confined space, near open 
flames or in direct sunlight. DO NOT leave a lit torch unattended.

1 x Lightweight Carry Stand

1 x Map Gas Regulator with built in flashback Arrestor

1 x Oxygen Regulator

1 x Oxygen flashback arrestor

1 x 2 Litre Oxygen Cylinder & 1 x Map gas cylinder

3 x Metre Oxygen/Fuel Gas Hose with fitted

         non return valves

Contents List

Page 2

Brazing Equipment

 

Warning

2 x Lightweight Brazing Nozzles

1 x Pepper Pot Nozzle

Triple Spark Lighter

Содержание Flametech Lite













Отзывы: