Hiniker 9850 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 33

background image

18 V-Plow Assembly

DWG. NO. 6474

WARNING: Disconnect truck battery
before beginning electrical installa-
tion to avoid shock hazard.

The motor solenoid, underhood wiring harness,
power cable and joystick control box are locat-
ed in the parts box shipped with the snowplow
frame.

NOTE:

Fill electrical connectors with dielectric

grease, and lightly coat ring and spade termi-
nals before installation to prevent corrosion.

8. Refer to drawing 6474. Lay the harness in

it’s approximate position for final assembly
with the 7-pin and 3-pin circular connectors
near the drivers side firewall, the 10-pin

and 3-pin connectors just left of center near
the grill, the relays near the drivers side in-
ner fender and the 5-pin headlight connec-
tors at the respective headlights.

9. Determine the location of the vehicle bat-

tery. If the battery is located on the right
(passenger) side or if there are two batter-
ies configured as a 12 volt system then pro-
ceed to step 10. If the battery is located on
the left side of the vehicle then the wiring
harness will need to be modified.

Truck Battery On Passenger Side

«
...
18
19
20
21
22
...
»

Содержание 9850


































Отзывы:

Нет отзывов

Похожие инструкции для 9850

Бренд: Napoleon Страницы: 2

Бренд: Dacor Страницы: 4

Бренд: SALSA Страницы: 2

BEA LZR-WIDESCAN

Бренд: Halma Страницы: 12

Бренд: Wahoo Страницы: 2

Бренд: Öhlins Страницы: 10

Бренд: +GF+ Страницы: 36

Бренд: Honda Страницы: 73

Бренд: Mobis Страницы: 16

Бренд: Mightymast Leisure Страницы: 5

Бренд: Subaru Страницы: 216

Powerbridge TSV

Бренд: Fishman Страницы: 2

Бренд: Prorack Страницы: 14

Бренд: Temposonics Страницы: 25

Бренд: Enviro Страницы: 37

Fresh Express Mov'

Бренд: Moulinex Страницы: 40

Бренд: hepco & becker Страницы: 5

Бренд: FixPosition Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды