manualshive.com logo in svg

Hiniker 700, Руководство оператора, Страница: 22 / 31

Поделиться
Скачать
Hiniker 700 Скачать руководство пользователя страница 22

20  Plow Assembly

18.  Locate three blue connector splices in the 

hardware bag in the plow’s parts box.

DWG NO. 4165

 

Using a blue splice, crimp the single brown 

wire  from  the  underhood  harness  into  the 

vehicle’s driver’s side parking light wire.

 

Using a blue splice, crimp the single yellow 

wire  from  the  underhood  harness  into  the 

vehicle’s driver’s side turn signal wire.

 

Using a blue splice, crimp the single green 

wire  from  the  underhood  harness  into  the 

vehicle’s curbside turn signal wire.

19.  Select the proper headlight adapter for your 

vehicle,  specific  instructions  are  included 

with each kit.

 

The  headlight  adapter  kit  consists  of  two 

identical adapters. Install the adapters ac-

cording to the instructions included with the 

kit  and  connect  to  the  5-pin  connectors  of 

the underhood wiring harness.

20.  Secure all cables away from hot or moving 

components with cable ties.

 

This completes the Electrical Installation.

21.  At  this  point,  the  mount  kit  should  be  as-

sembled onto the truck.

 

Prongs  from  the  truck  mount  kit  should 

be at a height that will slightly lift the plow 

frame  when  attaching  the  plow.  Prong  re-

ceivers on the plow frame should be paral-

lel to the ground when attaching the plow. 

Apply powered graphite on the truck prongs 

to  help  the  plow  to  slide  on  and  off  more 

easily.

REF.

NO.

PART

NUMBER

DESCRIPTION

QTY. REF.

NO.

PART

NUMBER

DESCRIPTION

QTY.

1

2

3

4

5

25011037

700-10904

951-003-014

950-004-076

392-010-010

Clamp

Machine Screw #6 - 32 X 1”

Locknut #6 - 32 Nylon Insert

Machine Screw #10 - 24 X 1 1/2”

Locknut #10 - 24 Nylon Insert

1

1

5

2

2

6

7

8

9

10

950-004-033

36716025

367-001-011

25010278

36716002

Machine Screw #6 - 32 X 1/2”

Nylon Lanyard 8”

Cable Tie 14”

Plug Mount Plate

Dust Cap

4

1

4

1

2

DWG NO. 3900

Содержание 700
































Отзывы:

Нет отзывов