Hiniker 700 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 31

Hiniker 700 Скачать руководство пользователя страница 19

Plow Assembly 17

Connect the RH headlamp to the wiring har-

ness end labeled “PSNGR SIDE” and the LH

headlamp to the end labeled “DRIVER SIDE”.

Ensure connections are fully mated for proper

sealing. There should be no gaps between

connector halves. Secure these cables to the

frame with plastic ties.

NOTE: Install the plow harness so that water does

not run down the wires and pool inside the “Y” con-

nection. Position the harness so that any trapped

water can easily drain away.

WARNING: Disconnect truck battery be-

fore beginning electrical installation to

avoid shock hazard.

8. The motor solenoid, underhood wiring har-

ness, power cable and joystick control box

are located in the parts box shipped with the

snowplow frame.

NOTE:

To prevent corrosion lightly coat all elec-

trical connections, ring and spade terminals with

dielectric grease prior to assembly.

Refer to drawing 6477. Lay the harness in

it’s approximate position for final assembly

with the 7-pin circular connector near the

drivers side firewall, the 10-pin connector

just left of center near the grill, the relays

near the drivers side inner fender and the

5-pin headlight connectors at the respective

headlights.

9. Determine the location of the vehicle bat-

tery. If the battery is located on the right

(passenger) side or if there are two batter-

ies configured as a 12 volt system then pro-

ceed to step 10. If the battery is located on

the left side of the vehicle then the wiring

harness will need to be modified.

DWG NO. 6477A

Truck Battery On Passenger Side

«
...
17
18
19
20
21
...
»

Содержание 700
































Отзывы:

Нет отзывов