Hiniker 700 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 31

Hiniker 700 Скачать руководство пользователя страница 9

the lift frame to fall forward, possibly causing

personal injury or damage to plow components.

With the plow lowered to the ground and the con-

troller in the “float” mode, push down on the up-

per lift links to fully retract the lift cylinder rod.

Retract Cylinder With Upper Lift Links DWG NO. 5693

Rotate the stop plate up to contact the spacer

bushing on the lift cylinder bolt.

Rotate Stop Plate DWG NO. 5695

Gently push back on the headlight bracket to tilt

the lift frame back as far as possible, then release

the bracket to allow the weight of the lift frame to

lock the stop plate in place.

Push Lift Frame Back DWG NO. 5697

Swing the latch handle open until the sliders are

fully removed from the attachment prongs.

Swing Handle to Remove Sliders DWG NO. 5694

Lower the parking stand to the ground by remov-

ing the tab lock pin from the front hole in the push

frame, then swinging the stand to the ground with

the lever.

Lower and Pin Parking Stand DWG NO. 5696

Reinstall the pin through matching holes in the

stand lever and push frame to hold the stand in

place.

Operating Procedures 7

«
...
7
8
9
10
11
...
»

Содержание 700
































Отзывы:

Нет отзывов