Hiniker 700 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 31

Hiniker 700 Скачать руководство пользователя страница 17

Plow Assembly 15

Turn the other two 90

O

adapters into ports

A and B from the back of the power unit so

that the flare ends point straight down.

DWG NO. 5702

Install 45

O

O-ring/flare adapters into the

ports of the angling cylinders so that the

flare ends of the adapters are directed

straight back.

Three identical hydraulic hoses are in the

parts box. Each hose has a swivel nut on

each end that will assemble to the adapters

from the power unit and three cylinders.

Connect one hose to the fitting from the

top of the power unit, then route the hose

ahead of the lift frame tube before assem-

bling to the fitting from the lift cylinder.

DWG NO. 6485

Connect the remaining two hoses to the fit-

tings from ports A and B at the back of the

power unit. Route both hoses ahead of the

lift frame tube before assembling the hose

from port A to the LH side angling cylinder

and the hose from port B to the RH side

angling cylinder.

DWG NO. 5700

Rotate the stop plate assembled to the push

frame up to contact the spacer bushing on

the lift cylinder bolt. Gently push back on

the upper lift frame tube, then release to al-

low the weight of the frame to lock the stop

plate in place.

5. Before assembling the power unit on the lift

frame, scrape a small amount of paint from

the two mount holes in the lift frame to pro-

vide a good electrical ground for the turn

signals and parking lights.

Mount the power unit on the lift frame with

two 3/8” x 3/4” hex bolts and two 3/8” lock

washers. The plastic reservoir of the power

unit should be to the left side of the plow.

DWG NO. 6484

Locate three 90

O

O-ring/flare adapters in

the hardware bag.

Turn the O-ring end of one adapter into the

top port of the power unit so that it points

about 45

O

to the right and to the rear when

viewed from the top.

«
...
15
16
17
18
19
...
»

Содержание 700
































Отзывы:

Нет отзывов