HIMA HIMatrix F3 DIO 16/8 01 Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 58

HIMA HIMatrix F3 DIO 16/8 01 Скачать руководство пользователя страница 48

4 Start-Up

F3 DIO 16/8 01

Page 48 of 58

HI 800 177 E Rev. 1.01

4.6.3 Two-pole

Connection with Common Ground

Two-pole channels can be interconnected on a common ground to allow line diagnosis,
e.g., with motors (dual motor drivers) or dual valves. The common ground is created via the
DO outputs of the channels concerned. To do so, the

DO[xx][xx].In Pairs

system parameter

must be configured for each pair (2 channels). For further configuration variants, also refer
to Table 23 and Table 28. If the line diagnosis is configured in pairs on both two-pole
channels (channel 1 and 2, channel 3 and 4, channel 5 and 6, channel 7 and 8), line
diagnosis is performed. To this end, set the

Line Monitoring [BOOL] ->

system variable in

SILworX to TRUE and the

DO[xx]-LSLB Monitoring

system signal in ELOP II Factory to

TRUE. If a test is performed on one channel, the second channel is switched off to ensure
that the line diagnosis is not distorted.

A short-circuit between the two DO+ lines is not detected.

A detected line fault is reported to the user:

In SILworX, with the system variables

-> + Error Code [WORD]

or

-> - Error Code

[WORD]

.

In ELOP II Factory, with the system signals

DO[xx].+Error Code

or

DO[xx].-Error Code

.

Load (Motor, Valve)

Free-Wheeling Diode

Figure 13:

Two-Pole Connection with Common Ground (Three-Pole Connection)

«
...
46
47
48
49
50
...
»

Содержание HIMatrix F3 DIO 16/8 01



























































Отзывы:

Нет отзывов