manualshive.com logo in svg

HIMA HIMatrix F3 DIO 16/8 01, Руководство пользователя, Страница: 41 / 58

Поделиться
Скачать
HIMA HIMatrix F3 DIO 16/8 01 Скачать руководство пользователя страница 41

F3 DIO 16/8 01 

4 Start-Up 

HI 800 177 E Rev. 1.01 

Page 41 of 58 

4.4.3 

Digital Inputs of F3 DIO 16/8 01 

System Signal 

R/W 

Description 

Mod.SRS [UDINT] 

R 

Slot number (System Rack Slot) 

Mod. Type [UINT] 

R 

Type of module, target value: 0x00E2 [226 

dez

] 

Module error code 
0x0000 

I/O processing, if required with errors, see other error 
codes  

0x0001 

No I/O processing (remote I/O not in RUN)  

0x0002 

No I/O processing during the booting test 

0x0004 

Manufacturer interface operating 

0x0010 

No I/O processing: wrong configuration 

0x0020 

No I/O processing: fault rate exceeded 

Mod. Error Code [WORD]  R 

0x0040/ 
0x0080 

No I/O processing: configured module not plugged in 

Error code of the DI supply unit as a whole: 

DI.Error Code Supply 
[WORD] 

R 

0x0001 Module 

fault 

Triggering the single DI supplies 
0x01 

Error DI supply unit 

0x02 

Supply shutdown due to over current 

DI[xx].Error Code Supply 
[BYTE] 

R 

0x04 

Error while reading back the supply 

Error codes for all digital inputs 
0x0001 

Fault within the digital inputs 

DI.Error Code [WORD] 

R 

0x0002 

FTT test of test pattern faulty  

Error codes for the digital input channels 
0x01 

Fault in the digital input module 

0x10 

Short-circuit of the channel 

DI[xx].Error Code [BYTE] 

R 

0x80 

Intermittence between pulsed output TO and digital 
input DI, e.g., 

ƒ

 Open-circuit 

ƒ

 Open 

switch 

ƒ

  L+ low voltage 

Input values for the digital input channels 
0 Input 

de-energized 

DI[xx].Value [BOOL] 

R 

1 Input 

enerized 

Number of pulsed outputs (supply outputs) 
0 

No pulsed output planned for LS/LB

1)

 detection 

1 

Pulsed output 1 planned for LS/LB

1)

 detection 

2 

Pulsed outputs 1 and 2 planned for LS/LB

1)

 detection 

DI Number of 
Pulsed Channels [USINT] 

W 

Pulsed outputs must not be used as safety-related outputs! 

Triggering the single DI supplies 
0 

Sensor supply (1 A) is off. 

1 

Sensor supply (1 A) is on. 

DI Supply[xx] [BOOL] 

W 

Default setting 0: feeding current 40 mA 

DI Pulse 
Slot [UDINT] 

W 

Pulse module slot 
(LS/LB

1) 

detection), set the value to 3 

Surce channel for pulsed supply 
0 Input 

channel 

1 

Pulse of the 1st TO channel 

DI[xx].Pulsed Channel 
[USINT] 

W 

2 

Pulse of the 2nd TO channel 

 

Содержание HIMatrix F3 DIO 16/8 01



























































Отзывы:

Нет отзывов