![background image](http://html1.mh-extra.com/html/hilti/te-60/te-60_original-operating-instructions_2135445028.webp)
1.
To adjust the position of the chisel, turn the
function selector switch until it engages in the
“Chisel adjustment” position.
2.
Bring the side handle into the desired position
and check that it is fitted correctly and secured.
3.
Rotate the chisel to the desired position.
4.
To lock the chisel in the desired position, turn the
function selector switch until it engages in the
“Chiseling” position. Do not operate the function
selector switch while the motor is running.
5.
To begin chiseling, plug the power tool’s supply
cord into the power outlet.
6.
Set the desired chiseling power (ATC).
NOTE
After connecting the supply cord to the
electric supply, the power tool is always set to
full chiseling power.
NOTE
To set the power tool to reduced (50%)
chiseling power, press the reduced-power but-
ton. The chiseling power LED then lights. To
reselect full chiseling power, press the reduced-
power button again.
7.
Position the tip of the chisel at the point where
chiseling is to begin.
8.
Press the control switch fully.
7.2.5 Drilling without hammering
Drilling without hammering is possible when drill bits
with a special connection end are used. Drill bits of
this kind are available from Hilti. For example, when
the keyless quick-release chuck is fitted, smooth-
shank drill bits for wood or steel can be used to
drill without hammering. The function selector switch
must be set to the “Hammer drilling” position when
the power tool is used in this way.
7.2.6 Control switch lock
8
When chiseling, the control switch can be locked in
the “on” position.
1.
Push the control switch lock above the grip
forward.
2.
Press the control switch fully.
The power tool then operates in sustained mode.
3.
To cancel sustained operating mode, slide the
control switch lock to the rear.
The power tool then switches off.
7.2.7 Mixing
1.
Turn the function selector switch until it engages
in the “Hammer drilling” position.
2.
Insert the quick-release chuck in the power tool’s
chuck.
3.
Insert the mixing paddle.
4.
Check that the insert tool has engaged correctly
by pulling it.
5.
Bring the side handle into the desired position
and check that it is fitted correctly and secured.
6.
Plug the supply cord into the power outlet.
7.
Position the mixing paddle in the container hold-
ing the substance to be mixed.
8.
To begin mixing, press the control switch slowly.
9.
Press the control switch fully to continue working
at full power.
10. Guide the mixing paddle carefully in order to
avoid splashing and spillage.
8. Care and maintenance
CAUTION
Disconnect the mains plug from the power outlet.
8.1 Care of core bits and metal parts
Remove any dirt adhering to the surface of the core
bits, the chuck and drive spindle and protect their
surfaces from corrosion by rubbing them with an oily
cloth from time to time.
8.2 Care of the power tool
CAUTION
Keep the power tool, especially its grip surfaces,
clean and free from oil and grease. Do not use
cleaning agents which contain silicone.
The outer casing of the power tool is made from
impact-resistant plastic. Sections of the grip are made
from a synthetic rubber material.
Never operate the power tool when the ventilation
slots are blocked. Clean the ventilation slots carefully
using a dry brush. Do not permit foreign objects to
enter the interior of the power tool. Clean the outside
of the power tool at regular intervals with a slightly
damp cloth. Do not use a spray, steam pressure
cleaning equipment or running water for cleaning.
This may negatively affect the electrical safety of the
power tool.
en
28
Содержание TE 60
Страница 32: ...en 32...
Страница 50: ...fr 50...
Страница 68: ...it 68...
Страница 100: ...sv 100...