8
English
2134962
*2134962*
5.1.2 Fitting the depth gauge (optional)
1. Release the side handle clamping band by turning the handle grip.
2. Slide the depth gauge from the front into the 2 guide holes provided.
3. Tighten the side handle clamping band by turning the handle grip.
5.1.3 Setting the power level (optional)
TE 60-ATC/AVR
After the supply cord is connected to the AC supply, the product is always set by default to full power.
1. Press the power reduction button. The product runs at reduced power (50 %).
▶
The reduced-power LED lights.
2. Press the power reduction button again. The product runs at full power.
▶
The reduced-power LED goes out.
5.1.4 Fitting the accessory tool
1. Apply a little grease to the connection end of the accessory tool.
▶
Use only genuine
Hilti
grease. Using the wrong grease can result in damage to the product.
2. Push the accessory tool into the chuck as far as it will go (until it engages).
3. After fitting the accessory tool, grip it and pull it in order to check that it is securely engaged.
▶
The product is ready for use.
5.1.5 Removing the accessory tool
CAUTION
Risk of injury by the accessory tool!
The accessory tool might be hot or have sharp edges.
▶
Wear protective gloves when changing the accessory tool.
▶
Pull the chuck back as far as it will go and remove the accessory tool.
5.2
Types of work
CAUTION
Risk of injury
Loss of control over the product.
▶
Check that the side handle is fitted correctly and tightened securely. Check that the clamping band is
engaged in the groove in the product.
Observe the safety instructions and warnings in this documentation and on the product.
5.2.1 Drilling with hammering action (hammer drilling)
1. Set the function selector switch to this symbol: .
2. Set the desired power level.
3. Press the drill bit against the work surface.
4. Press the control switch.
▶
The product starts.
5.2.2 Drilling without hammering
Drilling without hammering action is possible when accessory tools with a special connection end
are used. Accessory tools of this kind are available from
Hilti
. Alternatively, when the keyless quick-
release chuck is fitted, smooth-shank drill bits for wood or steel, for example, can be used to drill
without hammering.
▶
Set the function selector switch to this symbol:
.
Содержание TE 60-ATC-AVR
