background image

4 Technical data

Right of technical changes reserved.

PR 300-HV2S

Receiving range (diameter)

Typical distance with PRA 300: 2…600 m (6.56…

1,968.5 ft)

Range of remote control (circle diameter)

Typical distance with PRA 300, In the open field, with-

out external influences: 0…240 m (0…787.4 ft)

Accuracy

1

at 10 m (33 ft): ± 0.5 mm (0.02 in)

Plumb beam

Continuous, perpendicular to the plane of rotation

Laser class

Class 2, 620-690 nm; < 1 mW (EN 60825-1:2007 / IEC

60825-1:2007); Maximum power < 4.85 mW at ≧ 300

r.p.m.

Speed of rotation

600/min, 1,000/min (during the automatic alignment

procedure)

Inclination range

With the tool already inclined: ≤ 25%

Self-leveling range

±16° X-axis, ±10° Y-axis

Power source

7.2V/ 4.5 Ah Li‑ion battery

Battery life

Tempe25°C (+77 °F), Li‑ion battery: ≥ 25 h

Operating temperature range

-20…+50°C (−4…+122 °F)

Storage temperature range (dry)

-25…+60°C (−13…+140 °F)

Protection class

IP 66 (in accordance with IEC 60529); Not in “charging

during operation” mode

Tripod thread

⁵⁄₈" x 18

Weight (incl. PRA 84)

2.5 kg (5.51 lb)

Drop test height

2

1.5 m (4.92 ft)

1 Influences such as particularly high temperature fluctuations, dampness, shock, dropping, etc. can affect accuracy. Unless stated

otherwise, the tool was adjusted or calibrated under standard ambient conditions (MIL-STD-810G).

2 The drop test was carried out from a tripod, dropping onto flat concrete under standard ambient conditions (MIL-STD-810G).

PRA 300

Detection range (area diameter)

With the PR 300-HV2S (typical): 2…600 m (6.56…

1,968.5 ft)

Signal tone generator

3 volume levels plus mute setting

Liquid-crystal display

On both sides

Indicator range, distance from zero

± 52 mm (± 2 in)

Laser plane display range

± 1.0 mm (0.04 in)

Length of the detection area

120 mm (4.72")

Casing top edge center indicator

75 mm (2.95")

Marking notches

On both sides

Time without detection before automatic power off

15 min

Weight (including batteries)

0.25 kg (0.55 lb)

Power source

2 AA batteries

Battery life

Tempe20°C (+68 °F): Approx. 40 h (depending

on the quality of the alkaline batteries used)

Operating temperature range

-20…+50°C (−4…+122 °F)

Storage temperature range

-25…+60°C (−13…+140 °F)

1 The drop test was carried out using the PRA 83 receiver holder, dropped onto flat concrete under standard ambient conditions

(MIL-STD-810G).

en

7

Printed: 28.08.2015 | Doc-Nr: PUB / 5244524 / 000 / 00

Содержание PR 300-HV2S
































Отзывы: