Hillyard 108538 Скачать руководство пользователя страница 83

Страница: 83 / 117

6.5

Operating mode

VACUUM

Assumption

Action

Result

Machine ON
Operator Sitting

Vacuum Enabled
Forward pedal pressed

Squeegee Actuator goes down (+24V to M5)
Vacuum motor ON (+24V to M3)

Machine ON
Operator Sitting

Backward function enabled
during work

Squeegee Actuator rises (-24V to M5).

Machine ON
Operator Sitting

Traction Pedal not pressed
during work

Vacuum motor OFF after 10 seconds at maximum level.

Machine ON
Operator Sitting

Vacuum Disabled
during work

Squeegee Actuator rises (-24V to M5)
Vacuum Motor OFF after 10 seconds at maximum level.

RECOVERY TANK FLOATER

Assumption

Action

Result

Machine ON
Operator Sitting

Floater enabled
(full tank)

Floater ON (+24V to J8(12))
Vacuum motor OFF (ref to M4)
Brush motors OFF (ref to M3)

VACUUM WAND

Assumption

Action

Result

Machine ON
Operator Standing

Wand button enabled

Vacuum motor ON (+24V to M3)
Squeegee Actuator goes down (+24V to M5)

Machine ON
Operator Standing

Wand button disabled

Vacuum motor OFF (+0V to M3) after 10 seconds at
maximum level.
Squeegee Actuator rises (-24V to M5) after the next
traction consent.

Содержание 108538






















































































































Результаты поиска

Содержание 108538

Отзывы:

Похожие инструкции для 108538

Бренды по названию

Популярные бренды

Hillyard 108538, Руководство по обслуживанию

Результаты поиска

Содержание 108538

Отзывы:

Похожие инструкции для 108538

Бренды по названию

Популярные бренды