HIKVISION IPC-B220-IZ Скачать руководство пользователя | Manualshive

Страница: 5 / 39

background image

Network Bullet Camera

·

Quick Start Guide

4

4

Warnings

●

Proper configuration of all passwords and other security
settings is the responsibility of the installer and/or end-user.

●

In the use of the product, you must be in strict compliance with
the electrical safety regulations of the nation and region. Please
refer to technical specifications for detailed information.

●

Input voltage should meet both the SELV (Safety Extra Low
Voltage) and the Limited Power Source with 24 VAC or 12 VDC
according to the IEC60950-1 standard. Please refer to technical
specifications for detailed information.

●

Do not connect several devices to one power adapter as
adapter overload may cause over-heating or a fire hazard.

●

Please make sure that the plug is firmly connected to the power
socket. When the product is mounted on wall or ceiling, the
device shall be firmly fixed.

●

If smoke, odor or noise rise from the device, turn off the power
at once and unplug the power cable, and then please contact
the service center.

Cautions

serious injury or death.

injury or material damage.

«
...
3
4
5
6
7
...
»

Содержание IPC-B220-IZ








































Отзывы:

Нет отзывов

Похожие инструкции для IPC-B220-IZ

MACRO SPEEDLITE MR-14EX

Бренд: Canon Страницы: 2

Macro ring lite MR-14EX II

Бренд: Canon Страницы: 87

Бренд: Samsung Страницы: 2

Бренд: CADDX Страницы: 6

Бренд: Paradox Страницы: 2

Бренд: Paradox Страницы: 9

Бренд: Paradox Страницы: 35

Бренд: Dakota Alert Страницы: 18

Бренд: TRENDnet Страницы: 9

JV-B765HV9V22DNR

Бренд: JV vision Страницы: 12

Бренд: NAPCO Страницы: 4

Бренд: Q-See Страницы: 20

Бренд: Watts Страницы: 10

Бренд: Huviron Страницы: 56

Бренд: D-MAX Страницы: 47

Pursuit PRO-9649N

Бренд: Audiovox Страницы: 8

Бренд: Eagleye Страницы: 2

Бренд: System Sensor Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды