HIKVISION DS-K3B631TX Series Скачать руководство пользователя страница 7

Страница: 7 / 174

●

Do not ingest battery, Chemical Burn Hazard.

This product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it

can cause severe internal burns in just 2 hours and can lead to death.

Keep new and used batteries away from children. If the battery compartment does not close

securely, stop using the product and keep it away from children. If you think batteries might have

been swallowed or placed inside any part of the body, seek immediate medical attention.

●

If the product does not work properly, please contact your dealer or the nearest service center.

Never attempt to disassemble the device yourself. (We shall not assume any responsibility for

problems caused by unauthorized repair or maintenance.)

Cautions:

●

The equipment shall not be exposed to dripping or splashing and that no objects filled with

liquids, such as vases, shall be placed on the equipment.

●

Ensure correct wiring of the terminals for connection to an AC mains supply.

●

The equipment has been designed, when required, modified for connection to an IT power

distribution system.

●

+ identifies the positive terminal(s) of equipment which is used with, or generates direct current.

+ identifies the negative terminal(s) of equipment which is used with, or generates direct

current.

●

No naked flame sources, such as lighted candles, should be placed on the equipment.

●

This equipment is suitable for mounting on concrete or other non-combustible surface only.

●

Install the equipment according to the instructions in this manual.

●

To prevent injury, this equipment must be securely attached to the floor/wall in accordance with

the installation instructions.

●

Stainless steel may be corroded in some circumstances. You need to clean and care the device by

using the stainless steel cleaner. It is suggested to clean the device every month.

●

Do not drop the device or subject it to physical shock, and do not expose it to high

electromagnetism radiation. Avoid the equipment installation on vibrations surface or places

subject to shock (ignorance can cause equipment damage).

●

Do not place the device in extremely hot (refer to the specification of the device for the detailed

operating temperature), cold, dusty or damp locations, and do not expose it to high

electromagnetic radiation.

●

The device cover for indoor use shall be kept from rain and moisture.

●

Exposing the equipment to direct sun light, low ventilation or heat source such as heater or

radiator is forbidden (ignorance can cause fire danger).

●

Do not aim the device at the sun or extra bright places. A blooming or smear may occur

otherwise (which is not a malfunction however), and affecting the endurance of sensor at the

same time.

●

Please use the provided glove when open up the device cover, avoid direct contact with the

device cover, because the acidic sweat of the fingers may erode the surface coating of the device

cover.

●

Please use a soft and dry cloth when clean inside and outside surfaces of the device cover, do

not use alkaline detergents.

DS-K3B631TX Series Swing Barrier User Manual

Содержание DS-K3B631TX Series















































































































































































Результаты поиска

Содержание DS-K3B631TX Series

Отзывы:

Похожие инструкции для DS-K3B631TX Series

Бренды по названию

Популярные бренды

HIKVISION DS-K3B631TX Series, Руководство пользователя

Результаты поиска

Содержание DS-K3B631TX Series

Отзывы:

Похожие инструкции для DS-K3B631TX Series

Бренды по названию

Популярные бренды