HIKVISION DS-K1T643 Series Скачать руководство пользователя страница 126

Страница: 126 / 144

You can click the prompt to apply the changed data to the device. You can select either Apply

Now or Apply Later.

Figure 9-4 Data Synchronization

9.7 Configure Advanced Functions

You can configure the advanced functions of access control to meet some special requirements in

different scene.

Note

• For the card related functions(the type of access control card), only the card(s) with access group

applied will be listed when adding cards.

• The advanced functions should be supported by the device.

• Hover the cursor on the Advanced Function, and then Click to customize the advanced

function(s) to be displayed.

9.7.1 Configure Device Parameters

After adding the access control device, you can configure the parameters of access control device,

access control points.

Configure Parameters for Access Control Device

After adding the access control device, you can configure its parameters, including overlaying user

information on picture, uploading pictures after capturing, saving captured pictures, etc.
Before You Start

Add access control device to the client.
Steps

1. Click Access Control → Advanced Function → Device Parameter .

DS-K1T643 Series Face Recognition Terminal User Manual

111

Содержание DS-K1T643 Series

















































































































































Результаты поиска

Содержание DS-K1T643 Series

Отзывы:

Бренды по названию

Популярные бренды

HIKVISION DS-K1T643 Series, Руководство пользователя

Результаты поиска

Содержание DS-K1T643 Series

Отзывы:

Бренды по названию

Популярные бренды