HIKVISION DS-K1T643 Series Скачать руководство пользователя страница 90

Страница: 90 / 144

8.5.15 Set Image Parameters

Set the video standard, WDR, brightness, contrast, saturation, and sharpness.
Steps

1. Click Configuration → Image Adjustment .

Figure 8-10 Image Settings Page

2. Configure the parameters to adjust the image.

Video Standard

Set the video frame rate when performing live view remotely. After changing the standard,

you should reboot the device to take effect.
PAL

25 frames per second. Suitable for mainland China, Hong Kong (China), the Middle East

countries, Europe countries, etc.

NTSC

30 frames per second. Suitable for the USA, Canada, Japan, Taiwan (China), Korea, the

Philippines, etc.

WDR

Enable or disable the WDR function.
When there are both very bright and very dark areas simultaneously in the view, WDR

balances the brightness level of the whole image and provide clear images with details.

Brightness/Contrast/Saturation/Sharpness

Drag the block or enter the value to adjust the live video's brightness, contrast, saturation,

and sharpness.

Start/end recording video.

DS-K1T643 Series Face Recognition Terminal User Manual

Содержание DS-K1T643 Series

















































































































































Результаты поиска

Содержание DS-K1T643 Series

Отзывы:

HIKVISION DS-K1T643 Series, Руководство пользователя, Страница: 90 / 144

Результаты поиска

Содержание DS-K1T643 Series

Отзывы: