HIKVISION DS-K1T643 Series Скачать руководство пользователя страница 16

Страница: 16 / 144

Chapter 1 Overview

1.1 Overview

The face recognition terminal is a kind of access control device integrated with temperature

screening function. It can fast taking skin-surface temperature and upload abnormal temperature

event to the center, which can be widely applied in multiple scenarios, such as enterprises,

stations, dwellings, factories, schools, campus and so on.

1.2 Features

• Supports Vanadium Oxide uncooled sensor to measure target's temperature

• Temperature measuring range: 30 °C to 45 °C (86 °F to 113 °F), accuracy: 0.1 °C, deviation:

± 0.5 °C without black body calibration

• Recognition distance: 0.3 to 2 m

• Fast temperature measurement mode: Detects face and takes skin-surface temperature without

identity authentication.

• Multiple authentication modes are available: card and temperature, face and temperature, card

and face and temperature, etc.

• Face mask wearing alert

If the recognizing face does not wear a mask, the device will prompt a voice reminder. At the

same time, the authentication or attendance is valid.

• Forced mask wearing alert

If the recognizing face does not wear a mask, the device will prompt a voice reminder. At the

same time, the authentication or attendance will be failed.

• Displays temperature measurement results on the authentication page

• Triggers voice prompt when detecting abnormal temperature

• Configurable door status (open/close) when detecting abnormal temperature

• Transmits online and offline temperature information to the client software via TCP/IP

communication and saves the data on the client software

• Face recognition duration

＜

0.2 s/User; face recognition accuracy rate ≥ 99%

• 6000 face capacity, 10,000 card capacity, and 150,000 event capacity

• Suggested height for face recognition: between 1.4 m and 1.9 m

• Supports 6 attendance status, including check in, check out, break in, break out, overtime in,

overtime out

• Watchdog design and tamper function

• Audio prompt for authentication result

• NTP, manually time synchronization, and auto synchronization

• Connects to external access controller or Wiegand card reader via Wiegand protocol

• Connects to secure door control unit via RS-485 protocol to avoid the door opening when the

terminal is destroyed

DS-K1T643 Series Face Recognition Terminal User Manual

Содержание DS-K1T643 Series

















































































































































Результаты поиска

Содержание DS-K1T643 Series

Отзывы:

HIKVISION DS-K1T643 Series, Руководство пользователя, Страница: 16 / 144

Результаты поиска

Содержание DS-K1T643 Series

Отзывы: