HikRobot MV-CL042-91CC Скачать руководство пользователя страница 24

Страница: 24 / 120

Camera Link Line Scan Camera

User Manual

Attribute

Description

Digital IO Control

You can set the different input and output signals.

Counter and Timer
Control

You can view and set counter and timer related parameters.

File Access Control

You can view and set the device file access control related parameters.

Transport Layer
Control

You can set the parameters of transport layer of the device.

User Set Control

You can save or load the device’s parameters. You can set the default
parameter when running the client software.

6.2 Transport Layer Control

The camera’s tap geometry should match with that of the frame grabber, and inconsistent
parameters may lead to image exception.

In MVS client software, you can go to Transport Layer Control > Device Tap Geometry to check or
set the tap geometry. The CI Configuration displays the mode that the camera adopts currently.

Figure 6-2

Device Tap Geometry

For cameras of different models, the mode that the camera supports may differ. Pease refer to the
specification of the camera for details.

Содержание MV-CL042-91CC

























































































































Результаты поиска

Содержание MV-CL042-91CC

Отзывы:

Похожие инструкции для MV-CL042-91CC

Бренды по названию

Популярные бренды

HikRobot MV-CL042-91CC, Руководство пользователя

Результаты поиска

Содержание MV-CL042-91CC

Отзывы:

Похожие инструкции для MV-CL042-91CC

Бренды по названию

Популярные бренды