HIKOKI R 18DB, Инструкция по эксплуатации

Страница: 9 / 136

9
English
UNPACKING
Carefully unpack the power tool.
CHARGING
Battery and battery charger are not included with this
product.
For rechargeable batteries, please charge in according
to the handling instructions of the charger which you are
using.
MOUNTING AND OPERATION
Action Figure Page
Removing and inserting the battery
(sold separately)
2 2
Dismounting the dust case 3 2
Dismounting the fi lter 4 2
Check the fi lter
*1
5 2
Mounting the fi lter *2 6 3
Mounting the dust case
*3
7 3
Switch operation *4 8 3
The indicator lamp *5 9 3
How to use *6 10 4
Emptying the dust case *7 11 5
E ff ectively removing dust *8 12 5
Selecting accessories ― 130
*1 a. Filter free of debris and dust
b. Rubber not deteriorated
c. Connector free of damage
*2 If the fi lter is not properly fi tted, dirt or grime can enter
the fan unit and cause damage or malfunction.
*3 The dust case can also be installed with the nozzle
facing upwards. (
Fig. 7-a
)
*4
Mode
Continuous operating time
BSL1850/BSL36A18
3 (HIGH) Approx. 40 min.
2 (MID) Approx. 48 min.
1 (LOW) Approx. 66 min.
∗ Continuous operating time will vary according
to battery condition. Please use the table as a
guideline.
NOTE
To suppress noise when using the appliance,
switch to 1 mode.
*5 When the battery supply is low during operation of the
appliance, the indicator lamp will light up. When this
occurs, please recharge the appliance.
*6 When attaching the nozzle or extension pipe, insert as
you twist in the direction indicated by the arrow.
Twist in the direction indicated by the arrow when
detaching as well. (
Fig. 10-a
)
Twisting in the opposite direction could result in
detaching the dust case from the housing.
*7
NOTE
○ Point the intake port downward as dust can spill
when removing the dust case.
○ If the suction does not recover after disposing the
dust, clean the fi lter. (See “Cleaning the fi lter” on
page 9.)
*8 The appliance has a built-in mechanism for scraping
o ff dust attached to the fi lter when removing the dust
case.
To even more e ff ectively scrape o ff the dust, repeatedly
turn the dust case back and forth (2 to 3 times or more).
Holding the unit so that the dust case does not detach
from the housing, slightly and repeatedly turn the dust
case in the indicated directions.
MAINTENANCE AND INSPECTION
WARNING
○ For inspection and maintenance, be sure to turn o ff the
switch and disconnect the battery.
○ Do not work with wet hands. May cause electric shock
or injuries.
1. Cleaning the fi lter
CAUTION
○ Do not wash the fi lter in a washing machine.
○ Do not wash the fi lter in hot water or dry it by fi re.
○ Do not detach the fan fi lter and the fi lter holder.
If the vacuuming e ffi ciency is poor even when the dust
case has been emptied, remove the fi lter and wash it in
cold or warm water. (The water should not be hot to the
touch.)
After washing, dry out of direct sunlight. (
Fig. 13-a
)
If there is dust on the fan fi lter, hold the cleaner with the
fan fi lter pointing downwards to keep dust from entering
the motor and lightly clean with a small brush such as a
used toothbrush. Do not brush vigorously. (
Fig. 13-b
)
NOTE
○ Do not use gasoline, thinner, benzene or kerosene as
they can melt plastic.
○ Do not use an air gun or similar tool to clean the fi lter,
fan fi lter or the appliance itself. (
Fig. 13-c
)
Doing so could push dirt into the appliance and cause
malfunction.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws
be loose, retighten them immediately. Failure to do so
could result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very “heart” of the power
tool.
Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
4. Inspection of terminals
Check to make sure that swarf and dust have not
collected on the terminals.
On occasion check prior, during and after operation.
CAUTION
Remove any swarf or dust which may have collected on
the terminals.
Failure to do so may result in malfunction.
5. Cleaning of the outside
When the tool is stained, wipe with a soft dry cloth
or a cloth moistened with soapy water. Do not use
chloric solvents, gasoline or paint thinner, as they melt
plastics.
6. Storage
Store the cordless cleaner in a place in which the
temperature is less than 50°C and out of reach of
children.
When storing the appliance in a vertical position, hook
the strap to a hanger.
000Book̲R18DB̲EU.indb 9 000Book̲R18DB̲EU.indb 9 2020/07/10 9:49:39 2020/07/10 9:49:39