Hifonics Brutus Series, Руководство пользователя

Страница: 22 / 32

22
INTERCONNECTION EXAMPLE
Normal mode: subwoofer operation
FUNCTIONAL INSTRUCTIONS
INTERCONNECTION
• Connect the RCA lineouts of the head unit with the RCA jacks LINE IN of the amplifier with appropriate high-value RCA cables.
If your head unit is equipped with a additional subwoofer lineout (SUB OUT), it is recommended to use this lineout.
• Connect the subwoofer with the speaker outputs (SPEAKER / -) by using appropriate wires.
• Always ensure that the total impedance load on the speaker outputs is not lower than 1 ohm.
Too low impedance cause high temperature and will shut down the amplifier operation.
• Always ensure the correct polarity of the speakers. The interchange of plus and minus cause total loss of bass playback and could
damage the speakers.
MODE SWITCH
• The MODE switch must be in Position MASTER.
LEVEL CONTROLLER
• Turn the LEVEL controller of the amplifier to the MIN position.
• Turn the volume controller of the head unit to 80 - 90% of its full setting.
• Turn the LEVEL controller clockwise until you hear some distortion.
• Then turn back the LEVEL controller slightly until you hear a cleaner sound.
EXTENDED BASS CONTROL
• The SUB BOOST controller adjusts the bass enhancement between 0db and +18dB.
• A too high bass boost may cause clipping/distortion and damage on the loudspeakers and also may harm your hearing abilities.
Use this controller carefully! Refer for further information (EXTENDED BASS CONTROL) to page 20 (Section #5).
LOW PASS CONTROLLER
• The LP controller adjusts the cut-off point of the frequency range to above. The cut-off frequency is continuously
adjustable from 35 Hz to 250 Hz.
SUB SONIC CONTROLLER
• The SUB SONIC controller (Subsonicfilter) limits the ultralow and not hearable frequencies of the audiosignal to below, to avoid a
mechanical and electrical overloading on the subwoofer. The cut-off frequency is adjustable from 15 to 55 Hz and depends
on the size of the subwoofer.
PHASE CONTROLLER
• The PHASE controller allows to adjust the phasing between 0° and 180°.
Thereby you are able to adjust the subwoofer perfect to the vehicle’s acustics.
BASS REMOTE
• The enclosed BASS REMOTE CONTROLLER adjusts the bass-level e.g. from the driver’s seat.
Please use only the enclosed bass remote controller and cable.
POWER INPUT
SPEAKER OUTPUT
PROTECT
POWER
SLAVE MASTER
LP LEVEL
BASS LEVEL
CONTROLLER
AUTO TURN ON
(ONLY IN HI LEVEL INPUT MODE)
0dB 18dB
LINE IN SLAVE IN/OUT
LEVEL
INPUT
MODE
35Hz 250Hz
L
R
MIN MAX
OFF
ON
LOW
HI
SUB
BOOST Q-CONTROL PHASE
FREQ.
RANGE SUB SONIC
15Hz 55Hz
GND +12V REM
EXTENDED BASS CONTROL
WIDE NRW 20Hz 80Hz 0 ° 180 °
BALANCED
INPUT
BRX4000 D
L
R
BRX4000 D
BLUE / WHITE
LOG0
POWER INPUT
SPEAKER OUTPUT
PROTECT
POWER
SLAVE MASTER
LP
LEVEL
BASS LEVEL
CONTROLLER
AUTO TURN ON
(ONLY IN HI LEVEL INPUT MODE)
0dB 18dB
LINE IN SLAVE IN/OUT
LEVEL
INPUT
MODE
35Hz 250Hz
L
R
MIN MAX
OFF
ON
LOW
HI
SUB
BOOST Q-CONTROL PHASE
FREQ.
RANGE SUB SONIC
15Hz 55Hz
GND +12V REM
EXTENDED BASS CONTROL
WIDE NRW 20Hz 80Hz
0
°
180
°
BALANCED
INPUT
BRX4000 D
L
R
BRX4000 D
BLUE / WHITE
LOG0
Connect stereo RCA output (R/L or SUB OUT)
of the head unit with LINE IN R/L of the amplifier
An additional subwoo-
fer can be connected to the
non-occupied speaker out-
puts. In this case ensure
a impedance of 2 - 8 ohms
per subwoofer.
MASTER
Subwoofer
1 – 8 Ohms
Connect Bass Level
Controller with the
enclosed cable