manualshive.com logo in svg

Hidea HDF2.5, Руководство пользователя, Страница: 45 / 57

Поделиться
Скачать
Hidea HDF2.5 Скачать руководство пользователя страница 45

Maintanance

Installing the Propeller

Spline models

WARNING

• Be sure to install the thrust holder before installing the propeller, otherwise the lower case and

propeller boss could be damaged.

• Be sure to use a new cotter pin and bend the ends over securely. Otherwise the propeller could

come off during operation and be lost.

1. Apply corrosion resistant grease to the propeller shaft.

2. Install the thrust holder, and propeller on the propeller shaft.

3. Install the washer. Tighten the propeller nut until there is no forward-and-backward movement.

4. Align the propeller nut with the propeller shaft hole. Insert a new cotter pin in the hole and

bend the cotter pin ends.

If the propeller nut does not align with the propeller shaft hole after tightening it, loosen the nut

until it aligns with the hole.

Changing gear oil

NOTE:

• Be sure the outboard motor is securely fastened to the transom or a stable stand. You could be

severely injured if the outboard motor falls on you.

• Never get under the lower unit while it is tilted, even when the tilt support lever or knob is

locked. Severe injury could occur i1’ the outboard motor accidentally falls.

1. Tilt the outboard motor so that the gear oil drain screw is at the lowest point possible.

2. Place a suitable container under the gear case.

3. Remove the gear oil drain screw.

1.Gear oil drain screw

2.Oil level plug

41

Содержание HDF2.5


























































Отзывы:

Нет отзывов