HID Fargo DTC1000Me Скачать руководство пользователя

Страница: 75 / 84

December 2016

Page 5-11

PLT-01668, Version: 1.2

System Overview - Troubleshooting

5.2.4.1 Additional Printer Specific Tools

Label

Description

INFO

• Printer Type
• Firmware Version
• IP Address
• Flipper
• Lamination
• Magnetics
• E-Card
• Password
• Card count

TEST PRINTS

Color Photo:

Select this to print a color card to test communication and integrity.

Alignment:

Select this to print a card used to align the print image on the card.

Settings:

Select this to print a card with the Advanced settings.

Resin:

Select this to print a RESIN test card.

Rewritable:

Select this to ERASE the Rewritable card.

Magnetic:

Select this to test Magnetic encoding. (Hi-Co only)

Lamination:

Select this to laminate a test card.

Hopper Select

Ability to select which hopper to feed cards from. Applies to Dual Hopper Printers.

Toolbox

Clean Printer:

Select this to run the clean printer routine.

Clean Laminator:

Select this to run the clean laminator routine.

Calibrate Mag:

Select this to calibrate the Magnetic Sensor

Calibrate Rib Sensor:

Select this to calibrate the ribbon sensor.

Network:

Select this to configure network options.

Language

Select this choice to change the Printer Displayed Language.

Exit

Select this choice to exit the Printer Tool options.

Содержание Fargo DTC1000Me





















































































Результаты поиска

Содержание Fargo DTC1000Me

Отзывы:

Похожие инструкции для Fargo DTC1000Me

Бренды по названию

Популярные бренды

HID Fargo DTC1000Me, Руководство пользователя

Результаты поиска

Содержание Fargo DTC1000Me

Отзывы:

Похожие инструкции для Fargo DTC1000Me

Бренды по названию

Популярные бренды