HID Fargo DTC1000Me страница 39 Скачать руководство пользователя

Страница: 39 / 84

December 2016

Page 4-13

PLT-01668, Version: 1.2

Printer Preferences

4.1.1.5 Advanced Settings Tab

Use the Toolbox

Advanced Settings

tab for adjusting the internal printer settings, which are

customized for every printer at the factory and saved directly within the printer's memory.

Note:

Select

Restore Defaults

to restore the internal default settings.

Settings enable users to change the values for firmware settings by clicking on the Current column.

Field

Description

Setting Column

Displays label for setting. See the Setting Column Fields table below.

Default Column

Displays default value for setting

Current Column

Displays current value for setting

Apply Button

Applies changed values.

Restore Defaults Button

Restores the default values.

Enable Mag Verify

Check this box to verify that the data is written to the tracks correctly.

Содержание Fargo DTC1000Me





















































































Результаты поиска

Содержание Fargo DTC1000Me

Отзывы:

Похожие инструкции для Fargo DTC1000Me

Бренды по названию

Популярные бренды

HID Fargo DTC1000Me, Руководство пользователя

Результаты поиска

Содержание Fargo DTC1000Me

Отзывы:

Похожие инструкции для Fargo DTC1000Me

Бренды по названию

Популярные бренды