HID Fargo DTC1000Me Скачать руководство пользователя страница 72

Страница: 72 / 84

Page 5-8

December 2016

System Overview - Troubleshooting

PLT-01668, Version: 1.2

# 110
Card Jam/Align
error

A card is
jammed in the
print station or
card flipping
area of the
printer.

Clear the jam. Press the

Pause

button to continue.

# 111
Head Loading

An
unrecoverable
error has
occurred
during
printing.

Reset the printer and try again. If this problem persists, call for
technical assistance.

# 112
Card Jam/Align
error

A card is
jammed in the
print station or
card flipping
area of the
Printer.

Clear the jam. Press the

Pause

button to continue.

# 128
# 170
Calibrate Ribbon

The print
ribbon sensor
is out of
calibration or
has failed.

Calibrate the ribbon sensor.
Check for material blocking sensor and try again.

# 131
Flipper
Jam/Home Error

A card has
become
jammed in the
printer’s
flipper table.
The flipper
failed to
position
properly while
aligning a card
or flipping a
card.

Clear any cards in the flipper table, using the buttons to move the card
out.
Resume printing.
Reset the printer and retry. If problem persists call for technical
assistance.

# 136
Secure Guard
Print Disabled

Printing is
disabled by
SecureGuard
until a
password is
received.

Reset the printer and retry.
If the problem persists, call for technical assistance.

# 139
Please Remove
Ribbon

Ribbon needs
to be removed.

Reset the printer and retry.
If problem persists, call for technical assistance.

Error Message

Cause

Solution

Содержание Fargo DTC1000Me





















































































Результаты поиска

Содержание Fargo DTC1000Me

Отзывы:

Бренды по названию

Популярные бренды

HID Fargo DTC1000Me, Руководство пользователя

Результаты поиска

Содержание Fargo DTC1000Me

Отзывы:

Бренды по названию

Популярные бренды