background image

Installation BN48-IP66 

22

 

                                                                                                                                    Release 01    11/2019     

 

EMC and immunity 

 

EMC interference 
emission 

 

 

Radiated emission 

 

 

FCC 47 CFR Part 15 

 

Class A 

EN 55032 

 

Class A 

Conducted emission 

 

 

FCC 47 CFR Part 15 

 

Class A 

EN 55032 

 

Class A 

 

EMC interference 
immunity 

 

 

Electrostatic discharge 

 

 

EN 61000-4-2 
IEEE C37.90.3 

Contact discharge 

± 6 kV 

EN 61000-4-2 
IEEE C37.90.3 

Air discharge 

± 8 kV 

Electromagnetic field 

 

 

EN 61000-4-3 

80 MHz ... 6000 MHz 

10 V/m 

Fast transients (burst) 

 

 

EN 61000-4-4 

Power 

± 2 kV 

EN 61000-4-4 

Signal 

± 1 kV 

Voltage surges - AC 
supply connection 

 

 

EN 61000-4-5 

line/earth 

± 2 kV 

EN 61000-4-5 

line/line 

± 1 kV 

Voltage surges - data line   

 

EN 61000-4-5 

line/earth 

± 1 kV 

Conducted disturbances

   

 

EN 61000-4-6 

150 kHz ... 80 MHz 

10 V 

 

 

Network range 

 

10/100/1000 Mbit/s twisted pair 
port 

 

Length of a twisted pair segment 

max. 109 yards (100 m) (for Cat5e cable) 

 

 

Содержание BN48-IP66























Отзывы: