background image

15

SPECIFICATIONS

SYSTEM

Operating range

100 ft (30 m) typical

Frequency range

311/315 MHz or 868/915MHz 

HF output power

2 - 3 mW

Operating 
temperature range

-25° to +70° C 

(-18° F to 158° F)

Enclosures

IP65 weatherproof (exceeds NEMA 
12/13)

Programmable

I/O Logic, Interlocking, Latching 
Functions

HH-M-MFSHL TS5 TRANSMITTER

Weight

1.1 lbs, 500g (includes battery)

Dimensions 

Height

Width

Depth

8.0 in (205 mm)

5.2 in(132 mm)

3.4 in (86 mm)

Power supply

2 - 1.5V ’AA’ batteries

Operation time

Up to 500 hours

Functions

E-Stop pushbutton
5 motion toggle switches
Proportional grey code trigger 
switch

Antenna

Internal

HH-M-MFSHL TS6P TRANSMITTER

Weight

1.1 lbs, 500g (includes battery)

Dimensions 

Height

Width

Depth

8.0 in (205 mm)

5.2 in(132 mm)

3.4 in (86 mm)

Power supply

2 - 1.5V ’AA’ batteries

Operation time

Up to 500 hours

Functions

E-Stop pushbutton
6 motion toggle switches
Proportional grey code trigger 
switch

Antenna

Internal

HH-L-MFSHL TS7P TRANSMITTER

Weight

1.3 lbs, 590g (includes battery)

Dimensions 

Height

Width

Depth

8.4 in (214 mm)

5.8 in(148 mm)

3.4 in (86 mm)

Power supply

2 - 1.5V ’AA’ batteries

Operation time

Up to 500 hours

Functions

E-Stop pushbutton
7 motion toggle switches
Proportional grey code trigger 
switch

Antenna

Internal

RX-MFSHL DC16-PWM RECEIVER

Operating power

12/24 VDC (+/- 20%)

Current

<100 mA

Safety features

Self-monitoring E-Stop circuits

Short circuit protection on ESTOP 
contact

Over-current protection (10A limit)

Equipped with solid state relays

Self-test during start-up and 
operation

On-board diagnostic system with 
indicators for RF communication, 
power status, active outputs

Outputs

16 solid state switching outputs
2 PWM outputs
1 Main Contact output

Antenna

Internal

PRELIMINAR

Y COPY

Содержание HH-L-MFSHL TS7P




















Отзывы: