Herz BW/WW Скачать руководство пользователя | Manualshive

Страница: 7 / 65

background image

Safety notes

2

Betriebsanleitung_commotherm_5_15_SW_WW_Touch_Englisch_V1.2

7

2.3.1

Operation

Covers which prevent contact with hot or rotating parts or which are required in order to
direct the flow of air correctly and thus ensure the effective functioning of the system must
not be opened during operation.

In the event of a fault or unusual operating conditions the system is to be switched off
immediately. Notify the HERZ Customer Service department immediately.

The generated system noise during operation does not present any danger to the operator´s
health.

2.3.2

Maintenance

Before starting to carry out any work on the system, but especially before opening covers
protecting live parts, the system is to be properly disconnected from the power supply.
Besides the main circuits, attention is also to be paid to any existing additional or auxiliary
circuits in the process.

The normal safety rules according to ÖNORM are:



Disconnect all poles and all sides!



Ensure that the system cannot be switched on again!



Check to ensure that no voltage is connected!



Earth and short-circuit!



Cover adjacent live parts and locate hazardous areas

These above-mentioned measures must not be reversed until the system has been fully
installed and maintenance has been completed.

In order to prevent any maintenance errors, if maintenance is not carried out properly, it is recommended to
be carried out regularly by authorised personnel or by the HERZ Customer Service department.

Spare parts must be obtained directly from the manufacturer or a distribution partner. The customer will not
be exposed to any health risks as a result of the noise generated by the machine.

«
...
5
6
7
8
9
...
»

Содержание BW/WW


































































Отзывы:

Нет отзывов

Похожие инструкции для BW/WW

Бренд: Zoeller Страницы: 10

Бренд: NuTone Страницы: 8

Бренд: Oasis Aquatics Страницы: 14

SMART GEYSER 2330-03

Бренд: Simer Страницы: 12

Бренд: Garland Страницы: 100

Бренд: STIEBEL ELTRON Страницы: 20

SiFire EN 100/200-205-45 E

Бренд: Wilo Страницы: 108

PACIFIC HYDROSTAR 1/3 HP Submersible Sump Pump with Vertical Float...

Бренд: Pacific hydrostar Страницы: 9

Бренд: Racer Страницы: 108

AquaMax Eco Expert 5300

Бренд: Oase Страницы: 20

Бренд: Sulzer Страницы: 16

Бренд: Power Fist Страницы: 16

WSAN-XSC3 MF 200.4

Бренд: CLIVET Страницы: 68

Бренд: FLYGT Страницы: 172

Бренд: Heatcraft Refrigeration Products Страницы: 20

Бренд: veito Страницы: 40

ISMATEC ISM 940

Бренд: Fisher Bioblock Scientific Страницы: 41

FLYGT Flygt 2071

Бренд: Xylem Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды