Herz BW/WW Скачать руководство пользователя

Страница: 30 / 65

T-Control

Betriebsanleitung_commotherm_5_15_SW_WW_Touch_Englisch_V1.2

tin

ire

Term

Description

Unit

Overview

      

Mode

The definitive mode for the heat pump can be set here (OFF, Heating
mode, Cooling mode, Emergency mode).

OFF

In this mode the heat pump is switched off and does not supply any hot
or cold.

Heating mode

In this mode heat is supplied to the building of for hot water preparation.

Cooling mode

With the cooling operation, heat is removed from the building and
dispensed to the heat source.

Emergency mode

In this mode the heat pump is taken out of operation and only the
electrical heater serves as a source of heat.

Operation mode

The current operating condition of the heat pump is displayed here
(according to chapter 6).

Status I

      

Flow temperature

Display of the flow temperature of the heat pump in °C

°C

Back flow temperature Displays the back flow temperature of the heat pump in °C

°C

Source inlet
temperature

Display of the temperature of the source at the input to the heat pump
(air outside temperature) in °C

°C

Source outlet
temperature

Display of the temperature of the source at the output to the heat pump
in °C

°C

Hot gas temperature

Display of the temperature of the gaseous fluids after the compressor in
°C.

°C

Status II

      

High-pressure control

Display of the status‘ (OK/NOK) at the high pressure controller

Low-pressure control

Display of the status‘ (OK/NOK) at the low pressure controller

Outputs I

      

Source pump

Display for the condition of the fan:



When the control light flashes the ventilation is running and heat is fed
from the air via the evaporator into the cooling circuit.

Condensator pump

Display for the condition of the condensator pump:



When the control light flashes, the condenser pump (=heating pump)
is switched on and then supplies heat to the modules (Buffer, Hot
water tank, heating circuit) connected.

Compressor

Display for the condition of the compressor:



When the control light is flashing, the compressor is switched on and
the refrigerant is raised to a higher temperature and pressure level.

Oil sump heater

Display for the condition of the oil sump heating:



When the control light is flashing, the oil sump heating is switched on
which is necessary for the operation of the compressor

Outputs II

      

Electrical additional
heating

Display of the condition of the additional electrical heating:



When the pilot light is flashing, the additional electrical heating is
switched on and the storage tank is also brought to the temperature.



Additional electrical heating may be an e-bullet or an electrical heating
rod, for example.

Bivalent demand

Display for the condition of the bivalent requirement:



If the control light is flashing, there is heat requirement from another
heat generator

Содержание BW/WW


































































Результаты поиска

Содержание BW/WW

Отзывы:

Похожие инструкции для BW/WW

Бренды по названию

Популярные бренды

Herz BW/WW, Руководство по эксплуатации

Результаты поиска

Содержание BW/WW

Отзывы:

Похожие инструкции для BW/WW

Бренды по названию

Популярные бренды