background image

 

 

EQUIPMENT MISUSE HAZARD

Equipment misuse can cause the equipment to rupture, malfunction, or start unexpectedly 
and result in serious injury.

This equipment is for professional use only.

Read all instruction manuals, tags, and labels before operating the equipment.

Use the equipment only for its intended use.

Do not alter or modify this equipment.

Do not exceed the maximum working pressure of the lowest rated system component.

Do not operate the gun washer at a pressure above the maximum working pressure rating of the  

 

gun(s) being cleaned.

Route the hoses away from traffic areas, sharp edges, moving parts, and hot surfaces.

Do not use the hoses to pull the equipment.

Do not move pressurized equipment.

Use fluids or solvents that are compatible with the equipment wetted parts. Read the fluid and 

 

solvent manufacturer's warnings

Comply with all applicable local, state and national fire, electrical and other safety regulation.

PRESSURIZED EQUIPMENT HAZARD

Spray from hose leaks, ruptured components, or from operating the gun washer with an open lid 
can splash fluid in the eyes or on the skin and cause serious injury.

A safety device has been installed to shut off the pump when the gun washer lid is opened. 

 

Do not tamper with or alter this device.

Open the gun washer lid slowly.

Do not prop the gun washer lid open with an object or by any other means.

Do not stop or deflect fluid leaks with your hand, body, glove, or rag.

Tighten all fluid connections before operating the equipment.

Replace worn, damaged, or loose parts immediately.

WARNING

Page 3 of 20

Содержание G205





















Отзывы: