background image

Model HCH-930/932

2-9.  SOLID STATE DELAY TIMER

1. Disconnect the electrical supply to the cabinet.

To avoid electrical shock or property damage, move the
power switch to OFF and disconnect main circuit breaker,
or unplug cord at wall receptacle.

2. Remove the cabinet top.

3. Remove the 2 nuts securing the relay to the back of the control

panel.

4. Transfer the 5 relay wires, one-at-a-time, from the old relay to the

new one.

5. Mount the new relay on the back of the control panel with the 2

nuts removed earlier.

6. Replace the cabinet top.

7. Reconnect the electrical supply.

2-10.  BLOWER

1. Disconnect the electrical supply to the cabinet.

To avoid electrical shock or property damage, move the
power switch to OFF and disconnect main circuit breaker,
or unplug cord at wall receptacle.

2. Remove the cabinet top.

3. Remove the 2 blower wires from the L1 and L2 wire nuts.

                                              Step 4

4. Remove the 4 screws and lockwashers securing the blower to the

blower box, and remove blower.

5. Install new blower in reverse order of disassembly.

6. Reconnect the electrical supply to the cabinet.

2-6

              203

Solid State Delay Timer

Содержание HCH-930


























Отзывы: