Henny Penny Chick-fil-A Controls 500 Скачать руководство пользователя страница 14

Страница: 14 / 56

Henny Penny

Chick-fil-A Controls

2-4. WARNINGS AND
ERROR MESSAGES
(Continued)

ERROR CODES

DISPLAY

CAUSE

CORRECTION

(500 fryer only)

“E-26”

Faulty contactors or PC board.

Have the contactors and PC board checked.

“HEAT AMPS

ARE

LOCKED ON”

This error code could be displayed even with
the Cook/Pump switch turned OFF. Unplug
fryer or shut off the wall circuit breaker to
disconnect electrical power to fryer.

“E-41”

Memory scrambled. An individual

Turn the Cook/Pump switch OFF and back to

“SYSTEM

product program may be scrambled.

COOK. If error code persists, have the PC

DATA LOST”

Ex: “E-41 -2- DATA LOST”. This

board checked or re-initialized.

means product #2 program is
scrambled.

“E-46”

Faulty eprom or PC board.

Turn the Cook/Pump switch OFF and back to

“DATA SAVE

COOK. If error code persists, have the PC

FAILED”

board checked or re-initialized.

“E-70”

Faulty Cook/Pump switch

Have Cook/Pump switch checked, along with

“PWR SW

or switch wiring. Faulty

its wiring. Have I/O board checked.

OR WIRES

I/O board.

FAILED”

“E-92”

Blown 24 volt controller fuse, or

Have the 14-pin cable connector checked or

“24 VOLT

bad 14-pin cable connection.

have the fryer checked for a short to ground in

FUSE”

components such as the drain switch, solenoid,
or high limit.

Stuck or clogged solenoid valve.

Have solenoid checked and cleaned.

2-10

602

Содержание Chick-fil-A Controls 500

























































Результаты поиска

Содержание Chick-fil-A Controls 500

Отзывы:

Бренды по названию

Популярные бренды

Henny Penny Chick-fil-A Controls 500, Руководство пользователя

Результаты поиска

Содержание Chick-fil-A Controls 500

Отзывы:

Бренды по названию

Популярные бренды