background image

6 • 

Important: Always read and follow instructions.

Initial Screen

Dimensions gauge: pulling it out, it measures 

the wheel dimensions (

selects the correction type

displays the residual out-of-balance

(option) 

wheel locks/unlocks

main functions screen

(

 

MENU ACCESS DIAGRAM) 

 

 WHEEL DIMENSIONS 

SETTING).

If the machine remains on the initial screen for a cer-

tain amount of time without being used, the system 

is automatically switched to a screen-save. Striking 

of any key, movement of the wheel or di 

diameter gauge will cause automatic switching from 

the screen-save menu to the initial screen.

CAUTION

When the screensaver is active, automatic 
starting activated by the wheel guard is 
not available for safety reasons.

Standard Balancing (Clip-On Counter-

weights)

Wheel dimensions setting

Using the special grip, move the end of gauge 

against the rim as shown in the figure:

Hold the gauge in position for at least 2 seconds.

If the acoustic signal is enabled ( MENU - ACOUSTIC 

SIGNAL), the dimensions acquisition is accompanied 

by a beep.

Set the gauge to the rest position.
Set the width value shown on the tire and proceed 

with balancing the wheel.

If the wheel dimensions have been entered incor-

rectly, the parameters can be modified without repeat-

ing the balancing spin.

From the measurement screen press 

ENGLISH

...

Indicators, selection made

Push button, FUNCTIONS MENU

Push button, menu selection confirmation

Push button, cycle start

Push button, cycle stop

 -> 

ENGLISH

...

Indicators, selection made

Push button, FUNCTIONS MENU

Push button, menu selection confirmation

Push button, cycle start

Push button, cycle stop

.

Manual width setting

Press 

ENGLISH

...

Indicators, selection made

Push button, FUNCTIONS MENU

Push button, menu selection confirmation

Push button, cycle start

Push button, cycle stop

 / 

ENGLISH

...

Indicators, selection made

Push button, FUNCTIONS MENU

Push button, menu selection confirmation

Push button, cycle start

Push button, cycle stop

 to set the width “b” in 

manual mode.

Normally the “nominal” width is indicated on the 

wheel; otherwise, measure the dimension “b” with 

the supplied caliper gauge.

selects the correction type

displays the residual out-of-balance

(option) 

wheel locks/unlocks

main functions screen

(

 

MENU ACCESS DIAGRAM) 

 

selects the correction type

displays the residual out-of-balance

(option) 

wheel locks/unlocks

main functions screen

(

 

MENU ACCESS DIAGRAM) 

 

selects the correction type

displays the residual out-of-balance

(option) 

wheel locks/unlocks

main functions screen

(

 

MENU ACCESS DIAGRAM) 

 

selects the correction type

displays the residual out-of-balance

(option) 

wheel locks/unlocks

main functions screen

(

 

MENU ACCESS DIAGRAM) 

 

13

b

b

ENGLISH

Use and maintenance manual

selects

 

user control

/

/

selects the type of 
weight to be applied 

selects  the  manual 
dimension  presetting 
screen

returns  to  the  initial 
screen

In the standard machine setting as VIRTUAL SONAR (AWA and AUTOADAPTIVE enabled), at the end of the automatic 
distance and diameter measurement, perform a measuring spin.
In the case of particular rims, the wheel balancer may ask you to set the tyre width value in mm.

Set the width value shown on the tyre and proceed with balancing the wheel.

If  the  wheel  dimensions  have  been  entered  incorrectly,  the  parameters  can  be  modified  without  repeating  the 
balancing spin.

From the measurement screen press 

 -> 

 .

6.2.1.1 M

Press 

/

 to set the width “b” in manual mode.

Normally the “nominal” width is indicated on the wheel; otherwise, measure the dimension “b” with the supplied 
caliper gauge.

Use of the wheel balancer

Содержание Coats 1185

































Отзывы: