Hendi 289952, Руководство пользователя

Страница: 23 / 80

23
EN
B1. AUTO MODE SETTINGS
1. Turn on the device then press the
AUTO
PAUSE
button.
2. R0S1 will be displayed in the top right cor-
ner of the display. Enter the following pa-
rameters: temperature, time, and power (as
above).
3. Once the first step (R0S1) has been config-
ured, press the AUTO
PAUSE
button, and configure
the second step (R0S2). Program subsequent
steps (3 to 9) analogously to step one and two.
The factory settings of the device are such
that step 3 is the BOILING procedure and it
is the last step of the entire process – once
boiling is over the device will stop working.
If any additional steps are required between
step 2 and the boiling step, then change the
temperature setting in step 3 and configure
one of the subsequent steps as the boiling
process. Remember for the temperature ins
subsequent steps to be higher than in the
preceding step. In the BOILING stage, POW-
ER and TIMER may also be set. The default
temperature is set to 100°C. After setting the
power and timer press
AUTO
PAUSE
– the devise will
switch to hop adding reminder mode – de-
scribed in points 9 and 10 below.
4. Once all the needed steps have been con-
figured (as required – up to 9 steps), press
the
button to confirm all settings. The
device will start with R0S1, the first config-
ured step. R0S1 will flash on the display dur-
ing that time and the device will heat up the
water to the temperature set for that step
(R0S1). Once the pre-set temperature has
been reached, an acoustic signal will sound,
R0S1 and MASHING will flash on the dis-
play – this is a reminder to add ingredients.
Once the ingredients have been added, press
AUTO and the device will continue with step
R0S1 – heating at a pre-set temperature and
for a pre-set time. Once step R0S1 ends, the
device will move onto the next step – R0S2
and so on until the last configured step which
should entail BOILING.
5. Only one boiling process may be programmed
– once complete no more steps will be per-
formed. The boiling POWER can be set dur-
ing operation.
6. When the R0S1 step is completed, the device
will sound a reminder. The program will not
go to the next step until the
AUTO
PAUSE
button is
pressed. This is a reminder to add ingredi-
ents.
7. The reminder in the BOILING step works on
a similar principle to the reminder to add in-
gredients. Once the device ends the step be-
fore boiling – an acoustic signal will sound.
Press the
AUTO
PAUSE
button to confirm start of the
boiling step. This is a reminder for spraying
(sparging).
8.
AUTO
PAUSE
will stop the device and timer. Now the
parameters can be adjusted. Press the
AUTO
PAUSE
button again to continue operation.
9. To skip the current step in auto mode and go
to the next step press the button.
10. To set a reminder to add hops during the
boiling process: during step R0S3 (BOILING)
(according to factory settings, step R0S3 is
pre-set as the boiling step, but any other out
of the 9 available steps can be configured as
boiling) a reminder to ass hops may be con-
figured (and also its boiling time) – once the
heating power and boiling time on step R0S3
(BOILING) have been set, „HOP 1” will be
shown on the display and a flashing time val-
ue. Use
or buttons to set the time.
In order to add further hop reminders, press
the
button – 9 such reminders can be
set, however remember that the boiling time
(BOILING) has to be longer than the first hop
boiling time (HOP1), and the first hop boil-
ing time (HOP1) has to be longer than the
second hop boiling time (HOP2) and so on.
Therefore, boiling time (BOILING) > hop boil-
ing time HOP1 >hop boiling time HOP2 > hop
boiling time HOP3 > hop boiling time HOP4
> hop boiling time HOP5 > hop boiling time
HOP6 > hop boiling time HOP7 > hop boiling
time HOP8 > hop boiling time HOP9. Press
the
button to begin heating.
11. Press and hold the and buttons for
5 seconds with the display empty to switch
to recipe selection mode. Press
or
to choose the required recipe. Up to 10 reci-
pes may be pre-programmed. Press the
button to select the chosen recipe, the dis-
play will be empty, then press the
AUTO
PAUSE
button